Hotpoint Washing Machine WTL 500 Manual

The Hotpoint WTL 500 is a front-loading washing machine with a 5kg capacity, featuring multiple wash programs, energy-efficient operation, spin speed adjustments, delay timer, child lock, and self-cleaning functions. Designed for standard 220-240V AC, 50Hz power supply. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Front-loading drum, electronic control panel, detergent dispenser, water inlet valves, drain pump, adjustable feet, and emergency door release.

Installation

Unpack and remove all transit bolts and packaging materials.

1. Position the machine: Place on flat, stable floor near water supply and drain.
2. Connect water supply: Attach hoses to hot and cold water taps (if available) using supplied hoses.
3. Connect drain hose: Place drain hose into standpipe or sink (max height 100cm).
4. Level the machine: Adjust front feet to ensure machine is perfectly level.
5. Plug into grounded power outlet.

WARNING! Remove all transit bolts before first use. Ensure water connections are tight to prevent leaks.

First-Time Setup

After installation, run an empty wash cycle to clean the drum.

1. Connect power and turn on machine: Press POWER button.
2. Select cleaning cycle: Choose "Drum Clean" program or run a 90°C cotton cycle without laundry.
3. Add detergent: Pour washing machine cleaner or 100ml of detergent into drum.
4. Start cycle: Press START/PAUSE to begin cleaning cycle.
5. Set preferences: Configure default settings like spin speed, temperature via PROGRAM button.

CAUTION! Do not load laundry during first cleaning cycle. Ensure transit bolts are removed.

Specifications

• Model: Hotpoint WTL 500
• Capacity: 5kg
• Energy Rating: A++
• Water Consumption: Approx. 45 liters per cycle (cotton 60°C)
• Spin Speed: Up to 1200 rpm
• Programs: 12 wash programs including special cycles
• Noise Level: 55 dB (washing), 75 dB (spinning)
• Power Supply: 220-240V AC, 50Hz, 10A
• Dimensions: 85 x 60 x 55 cm (H x W x D)
• Weight: 65kg

Controls and Settings

Control Panel: POWER button, PROGRAM selector, TEMPERATURE button, SPIN SPEED button, DELAY START, CHILD LOCK, START/PAUSE.

Program Selection: Rotate PROGRAM knob to select: Cotton (40°C, 60°C, 90°C), Synthetic, Delicate, Quick Wash (30 min), Wool, Rinse & Spin, Drum Clean.

Temperature Settings: Cold, 30°C, 40°C, 60°C, 90°C (depending on program).

Spin Speed: No spin, 400 rpm, 600 rpm, 800 rpm, 1000 rpm, 1200 rpm.

Special Functions: Delay Start (1-24 hours), Child Lock (press 3 seconds), Extra Rinse, Pre-wash.

Connecting Water Supply

Connect to both hot and cold water supplies for optimal performance.

1. Turn off water taps before connecting hoses.
2. Connect blue hose to cold water tap, red hose to hot water tap (if available).
3. Use supplied washers and tighten connections by hand, then quarter turn with pliers.
4. Open water taps fully and check for leaks.
5. For single connection, connect both hoses to cold water tap using Y-connector.

Tip: Install inlet hose filters if water is hard to prevent valve blockage.

Using Wash Programs

Select appropriate program based on fabric type and soil level.

1. Sort laundry: Separate by color, fabric type, and soil level.
2. Load machine: Do not exceed 5kg maximum capacity.
3. Add detergent: Use drawer compartments I (pre-wash), II (main wash), * (fabric softener).
4. Select program: Turn PROGRAM knob to desired cycle.
5. Adjust settings: Set temperature, spin speed, and additional options.
6. Start cycle: Press START/PAUSE button.
7. End of cycle: Machine beeps; remove laundry promptly to prevent wrinkles.

WARNING! Do not wash waterproof items or items with flammable substances. Close zippers and fasten hooks before washing.

Special Functions

Delay Start: Set 1-24 hours delay. Child Lock: Press and hold for 3 seconds to activate/deactivate. Extra Rinse: Adds additional rinse cycle. Pre-wash: For heavily soiled laundry. Drum Clean: Run monthly without laundry to prevent odors.

Care & Cleaning

Monthly maintenance: Clean detergent drawer, door seal, and run drum clean cycle. Every 3 months: Check and clean drain pump filter.

1. Unplug machine before cleaning.
2. Wipe exterior with damp cloth; do not use abrasive cleaners.
3. Clean detergent drawer: Remove and wash under running water.
4. Clean door seal: Wipe rubber gasket to remove lint and residue.
5. Clean drain filter: Open filter cover at front bottom, place towel, unscrew filter, clean debris.

CAUTION! Never use harsh chemicals or steam cleaners. Ensure filter is properly tightened after cleaning.

Regulatory Information

CE certified. Complies with EU directives for safety and electromagnetic compatibility. Energy label according to EU regulation 2019/2014. Manufactured by Hotpoint, a brand of Whirlpool Corporation. For support, visit www.hotpoint.eu or contact customer service at 0800-316-1444.

Troubleshooting

Reset: Unplug for 5 minutes to reset electronic control.

Service: 0800-316-1444; www.hotpoint.eu