Hotpoint washing machine WMUD 843P manual

The Hotpoint WMUD 843P is a freestanding 8kg capacity washing machine with an A+++ energy rating, 1400 rpm spin speed, and multiple wash programs including Cotton, Synthetic, Delicates, Wool, Quick Wash, and Steam Refresh. It features a large LED display, delay timer, child lock, anti-flood system, and anti-vibration design. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Programs 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 8kg drum, LED control panel, detergent drawer, water inlet valves, drain pump, adjustable feet, and power cord.

Feature	Description
Capacity	8kg (dry laundry weight)
Energy Rating	A+++ (most efficient)
Spin Speed	Up to 1400 rpm
Display	LED with time remaining and program indicators
Programs	14 programs including Cotton, Eco, Quick 30'
Special Functions	Delay Start, Extra Rinse, Pre-Wash, Child Lock
Water Inlet	Cold fill only (hot fill optional with adapter)
Dimensions (HxWxD)	850 x 595 x 545 mm
Noise Level	Wash: 53 dB, Spin: 73 dB
Anti-Vibration	Yes, with adjustable feet and counterweight

Installation

Unpack and remove transit bolts. Place on level, solid floor.

Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
Adjust feet: Turn clockwise to raise, anti-clockwise to lower; ensure machine is level.
Connect water supply: Attach inlet hose to cold water tap (3/4" thread).
Connect drain hose: Place in standpipe or sink (max height 100 cm).
Plug into grounded power outlet.

WARNING! Do not install in wet areas. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle.

Check installation: Ensure all hoses are secure and machine is level.
Power on: Plug in and press Power button.
Run empty wash: Select Cotton 90°C program without laundry to clean drum.
Set preferences: Use Settings button to adjust buzzer volume, etc.
Load detergent: Fill drawer compartments as per detergent instructions.

CAUTION! Do not use machine without removing transit bolts. Use two people for moving.

Specifications

Model: WMUD 843P
Capacity: 8 kg
Energy Class: A+++
Annual Energy Consumption: 150 kWh
Water Consumption: 52 litres per cycle (Cotton 60°C)
Spin Speed: 1400 rpm
Noise Level: Wash 53 dB, Spin 73 dB
Programs: 14 including Cotton, Synthetic, Delicates, Wool, Quick 30', Steam Refresh
Dimensions: 850 x 595 x 545 mm (HxWxD)
Weight: 69 kg
Power Supply: 230-240V ~ 50Hz, 10A

Controls and Settings

Control Panel: POWER button, Program selector knob, LED display, Start/Pause, Delay, Extra Rinse, Pre-Wash, Child Lock buttons.

Programs: Cotton (20°C-90°C), Eco Cotton 40°C, Synthetic, Delicates, Wool, Hand Wash, Quick 30', Daily 60', Steam Refresh, Drum Clean, Spin Only, Rinse & Spin, Drain.

Settings: Press and hold Settings button to adjust end-of-cycle buzzer (On/Off/Volume). Delay Start: Press Delay to set 1-24 hours. Child Lock: Press and hold Child Lock for 3 seconds to activate/deactivate (default off).

Connecting Water & Drain

Water Inlet: Cold fill only (max pressure 1 MPa, min 0.05 MPa). Drain: To standpipe or sink.

Turn off water tap before connecting hose.
Connect inlet hose to machine (right side) and tap; hand-tighten only.
Place drain hose in standpipe (max height 100 cm) or over sink edge.
Ensure no kinks in hoses.

Tip: Use hose clips if drain hose does not stay in place. Check for leaks after first connection.

Using Wash Programs

Select program based on fabric type and soil level.

Load laundry: Do not overload; distribute evenly.
Add detergent: Open drawer; use compartments I (pre-wash), II (main wash), * (fabric softener).
Select program: Turn knob to desired program.
Adjust options: Press Extra Rinse, Pre-Wash, or Delay as needed.
Start: Press Start/Pause; door locks and cycle begins.
Pause/Stop: Press Start/Pause to pause; turn knob to reset to stop.
End of cycle: Buzzer sounds; door unlocks after a few minutes.

WARNING! Do not open door during spin cycle. Remove laundry promptly after cycle to prevent odors.

Special Functions

Delay Start: Delays start by 1-24 hours. Extra Rinse: Adds extra rinse cycle. Pre-Wash: For heavily soiled items. Child Lock: Locks controls (hold button 3 seconds). Steam Refresh: Reduces wrinkles and odors (without detergent). Drum Clean: Runs maintenance cycle (use monthly).

Care & Cleaning

Monthly maintenance: Run Drum Clean program (without laundry). Clean detergent drawer: Remove and rinse under water. Clean door seal: Wipe with damp cloth; remove debris. Clean filter: Turn off machine; open filter cover at front bottom; place towel; unscrew filter; clean; reinsert.

CAUTION! Unplug before cleaning filter. Do not use abrasive cleaners on door or drum.

Regulatory Information

CE marked; complies with EU directives for safety and EMC. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.hotpoint.eu or contact 0344 822 4224 (UK).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine does not start	Power, door, child lock	Check plug; ensure door closed; deactivate child lock.
No water intake	Tap, hose, filter	Ensure tap is on; check hose for kinks; clean inlet filter.
Water does not drain	Drain hose, pump filter	Check drain hose height; clean pump filter.
Excessive vibration/noise	Transit bolts, leveling, load	Ensure transit bolts removed; adjust feet; redistribute load.
Error codes (e.g., F01, F02)	Faults	Refer to manual error code list; unplug for 5 minutes; retry.
Detergent drawer blocked	Detergent residue	Remove drawer; clean under hot water.

Reset: Unplug for 5 minutes; plug back in.

Service: 0344 822 4224; www.hotpoint.eu