Hotpoint Washing Machine WML 540 P Manual

The Hotpoint WML 540 P is a freestanding washing machine with a 5 kg load capacity, featuring multiple wash programs, energy efficiency class A, spin speed up to 1000 rpm, delay timer, child lock, and imbalance control. Designed for standard household use with cold and hot water fill options. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Control panel with program selector, detergent dispenser, drum, door with safety lock, water inlet valves, drain pump, adjustable feet, and power cord.

Installation

Unpack and remove transit bolts. Place on level, solid floor.

1. Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
2. Adjust feet: Turn clockwise/anti-clockwise to level machine; use spirit level.
3. Connect water inlet: Attach cold/hot water hoses to taps; use supplied washers.
4. Connect drain hose: Place in sink or standpipe (max height 100 cm).
5. Plug into grounded power outlet.

WARNING! Do not install in wet areas. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a cotton cycle at 90°C without laundry.

1. Check installation: Ensure hoses are secure, drain hose positioned correctly.
2. Add detergent: Pour into compartment II (main wash) of dispenser.
3. Select program: Turn selector to Cotton 90°C.
4. Start: Press Start/Pause; machine will fill, heat, and complete cycle.
5. Set preferences: Use option buttons for spin speed, temperature, etc.

CAUTION! Ensure door is fully closed before starting. Keep children away during operation.

Specifications

• Model: Hotpoint WML 540 P
• Capacity: 5 kg (cotton)
• Spin Speed: 1000 rpm (adjustable)
• Programs: 12 programs including Cotton, Synthetic, Delicate, Quick Wash (30°C), Wool, Hand Wash, Rinse & Spin, Drain
• Dimensions (HxWxD): 85 x 60 x 50 cm
• Water Pressure: 0.5 - 10 bar
• Power Supply: 220-240V, 50Hz
• Energy Consumption: 0.95 kWh per cycle (cotton 60°C)
• Noise Level: Wash 56 dB, Spin 76 dB

Controls and Settings

Control Panel: Program selector, Start/Pause, Option buttons (Temperature, Spin, Delay), LED display.

Program Selector: Turn to choose wash program (Cotton, Synthetic, etc.). Option Buttons: Adjust temperature (cold to 90°C), spin speed (0 to 1000 rpm), delay timer (1-24 hrs). Start/Pause: Starts or pauses cycle. Child Lock: Press and hold Temperature + Spin for 3 seconds to activate/deactivate.

Detergent Dispenser: Compartment I (pre-wash), II (main wash), III (fabric softener). Follow dosage instructions on detergent packaging.

Connecting Water & Drain

Water Inlet: Connect hoses to cold/hot water taps (blue/red markings). Drain: Place hose in sink or standpipe.

1. Turn off taps before connecting hoses.
2. Use supplied washers; tighten by hand, then a quarter turn with pliers.
3. Ensure drain hose is not kinked and is secured to prevent slipping.
4. After connection, turn on taps and check for leaks.

Tip: Use drain hose extension if needed; max length 150 cm.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Do not exceed 5 kg; distribute evenly.
2. Add detergent: Use compartments I/II as needed; fabric softener in III.
3. Select program: Turn selector (e.g., Cotton for cottons, Synthetic for synthetics).
4. Adjust options: Set temperature, spin speed, delay if required.
5. Start: Press Start/Pause; door locks and cycle begins.
6. End of cycle: Machine beeps; door unlocks after a short delay.
7. Unload: Remove laundry promptly to avoid wrinkles.

WARNING! Do not open door during wash/spin; wait for unlock indicator.

Special Functions

Delay Timer: Set 1-24 hours delay start. Child Lock: Locks control panel. Imbalance Control: Auto-redistributes load during spin. Rinse Hold: Holds water after final rinse for easy hand washing removal.

Care & Cleaning

Regularly clean detergent dispenser, door seal, and filter.

1. Detergent dispenser: Pull out, rinse under warm water.
2. Door seal: Wipe with damp cloth to remove lint/residue.
3. Filter: Locate at front bottom; turn counter-clockwise to open; clean under running water.
4. Drum: Run empty hot wash (90°C) monthly with drum cleaner.

CAUTION! Unplug before cleaning. Do not use abrasive cleaners.

Regulatory Information

Complies with EU directives for safety (EN 60335-1, EN 60335-2-7) and electromagnetic compatibility (EN 55014-1, EN 55014-2). Energy label according to EU regulation 1061/2010. Disposal: Follow local regulations for WEEE. For support, visit www.hotpoint.eu or contact 08448 224 224 (UK).

Troubleshooting

Reset: Unplug for 1 minute, then restart.

Service: 08448 224 224; www.hotpoint.eu