Hotpoint Washing Machine WMA30 Aquarius Manual

The Hotpoint WMA30 Aquarius is a freestanding washing machine with a 6kg capacity, 1200 RPM spin speed, A+++ energy rating, and multiple wash programs. It features Aquarius technology for efficient water usage, electronic controls, delay start, child lock, and various safety mechanisms. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Programs 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Electronic control panel, detergent dispenser, drum, filter, water inlet hoses, drain hose.

FeatureDescription
Capacity6kg laundry load
Spin Speed1200 RPM maximum
Energy RatingA+++ for energy efficiency
Aquarius TechnologyOptimizes water consumption
ProgramsCotton, Synthetic, Delicate, Quick Wash, etc.
Delay StartUp to 24 hours
Child LockPrevents accidental program changes
DisplayLED indicators and time remaining
Door LockAutomatic during cycle
Adjustable FeetFor leveling on uneven floors

Installation

Unpack and remove transit bolts. Place on solid, level floor.

  1. Remove transit bolts: Use spanner to remove four bolts at rear; keep for future moves.
  2. Connect water supply: Attach inlet hoses to cold water tap (blue marker) and machine.
  3. Connect drain hose: Place in standpipe or sink; secure to avoid slipping.
  4. Level machine: Adjust feet using wrench; ensure no rocking.
  5. Plug into grounded power outlet.

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first wash, run a maintenance cycle.

  1. Power on: Plug in and press power button.
  2. Run empty cycle: Select Cotton program at 90°C without laundry.
  3. Set preferences: Use settings button to adjust beep volume, end signal.
  4. Load detergent: Fill dispenser compartments as per instructions.
  5. Start first wash: Load laundry, select program, press start.

CAUTION! Ensure transit bolts are removed; failure to do so can cause severe damage.

Specifications

Controls and Settings

Control Panel: Power button, program selector knob, temperature button, spin speed button, start/pause, options (delay, extra rinse, etc.).

Program Selection: Turn knob to desired program (e.g., Cotton, Synthetic). LED indicates selection.

Temperature: Press temperature button to cycle through options (cold, 30°C, 40°C, 60°C, 90°C).

Spin Speed: Press spin button to adjust (RPM: 400, 600, 800, 1000, 1200, or no spin).

Options: Delay start (1-24h), extra rinse, pre-wash, quick wash (reduces time).

Child Lock: Press and hold start button for 3 seconds to activate/deactivate.

Connecting Water Supply

Use supplied hoses; ensure correct inlet.

  1. Turn off water tap.
  2. Connect hose to cold water inlet (blue) on machine; hand-tighten.
  3. Connect other end to tap; use washer for seal.
  4. Open tap slowly; check for leaks.
  5. For hot water (if compatible), connect to red inlet.

Tip: Do not overtighten; use two wrenches to avoid damaging fittings.

Using Wash Programs

Select based on fabric type and soil level.

  1. Sort laundry: Separate by color and fabric.
  2. Load drum: Do not overload; leave space for movement.
  3. Add detergent: Use compartment I (pre-wash), II (main wash), * (softener).
  4. Select program: Turn knob (e.g., Cotton for cottons).
  5. Adjust settings: Temperature, spin speed, options.
  6. Start: Press start/pause; door locks automatically.
  7. After cycle: Remove laundry promptly; leave door ajar to dry drum.

WARNING! Do not open door during cycle; wait for unlock signal. Remove coins/objects from pockets.

Safety Features

Child Lock: Locks controls when activated. Door Lock: Prevents opening during wash/spin. Overflow Protection: Automatically stops water if detected. Imbalance Control: Reduces spin speed if load is uneven. Thermal Cut-out: Prevents overheating.

Care & Cleaning

Monthly maintenance recommended.

  1. Clean detergent drawer: Remove and rinse under water.
  2. Clean filter: Locate at front bottom; turn counterclockwise to remove; clear debris.
  3. Clean drum: Run hot wash (90°C) without laundry monthly.
  4. Wipe exterior: Use damp cloth; no abrasive cleaners.
  5. Check hoses: Inspect for cracks annually.

CAUTION! Unplug before cleaning. Do not use steam or high-pressure cleaners.

Regulatory Information

Complies with EU directives for safety (EN 60335), EMC (EN 55014), and energy labeling (EU 2019/2014). Manufactured by Hotpoint, a brand of Whirlpool Corporation. For support, visit www.hotpoint.co.uk or contact 03448 226 226. Keep manual for future reference.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine won't startPower/child lockCheck plug; ensure child lock off; close door firmly.
No water intakeTaps/hoses/kinksOpen taps; check hose for kinks; clean inlet filter.
Water leaksLoose connectionsTighten hoses; check detergent drawer seating.
Excessive vibrationTransit bolts/levelingEnsure transit bolts removed; adjust feet for level.
Drum not spinningOverload/imbalanceRedistribute load; reduce weight.
Error codes (e.g., F01)Various faultsConsult manual; unplug for 5 minutes, restart.
Poor wash resultsDetergent/programUse correct detergent amount; select suitable program.

Reset: Unplug for 5 minutes, then restart.

Service: 03448 226 226; www.hotpoint.co.uk

Hotpoint Washing Machine WMA30 Aquarius Manual © - All Rights Reserved 2025