Hotpoint Washing Machine WDUD 9640K Manual

The Hotpoint WDUD 9640K is a 9 kg capacity front-loading washing machine with 1400 RPM spin speed, A+++ energy rating, and advanced features including Direct Spray technology, Anti-Allergy cycle, Steam Refresh, and multiple specialized programs. It features a large LED display, intuitive controls, and AquaStop leak protection. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Washing Programs 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Front-loading drum, LED control panel, detergent dispenser, water inlet valves, drain pump, and adjustable feet.

Feature	Description
Capacity	9 kg laundry load
Spin Speed	Up to 1400 RPM
Energy Rating	A+++ (most efficient)
Direct Spray Technology	Sprays water during wash for better detergent dissolution
Anti-Allergy Cycle	Eliminates 99.9% of allergens with high-temperature wash
Steam Refresh	Reduces wrinkles and odors without washing
AquaStop	Full leak protection system
LED Display	Shows time remaining, cycle stage, and settings
Quick Wash	30-minute cycle for lightly soiled loads
Delay Start	Program start time up to 24 hours

Installation

Unpack and inspect contents. Place on level, solid floor.

Remove transit bolts: Use spanner to remove all four bolts from rear; keep for future moves.
Connect water supply: Attach inlet hoses to hot/cold taps (if applicable) and machine inlets.
Connect drain hose: Place in standpipe or sink; ensure no kinks.
Level the machine: Adjust front feet; use spirit level.
Plug into grounded power outlet.

WARNING! Do not install in areas with freezing temperatures. Ensure transit bolts are removed before use.

First-Time Setup

Power on machine; run initial calibration cycle.

Select language: Press SETTINGS button, choose language.
Run drum clean: Select "Drum Clean" program without laundry.
Set default options: Configure beep volume, child lock, etc.
Load detergent: Fill compartments as per detergent type.

CAUTION! First wash may contain residual water from factory testing; this is normal.

Specifications

Model: WDUD 9640K
Capacity: 9 kg (cotton)
Spin Speed: 1400 RPM (adjustable)
Energy Class: A+++
Water Consumption: Approx. 50 liters per cycle (cotton 60°C)
Noise Level: Wash: 53 dB, Spin: 75 dB
Dimensions (HxWxD): 85 x 60 x 60 cm
Weight: 72 kg
Power Supply: 220-240V, 50Hz
Programs: 15 including Cotton, Synthetic, Delicate, Wool, Sport, etc.

Controls and Settings

Access via rotary dial and touch buttons. Display shows cycle time, temperature, spin speed.

Main Controls: POWER, START/PAUSE, rotary program selector, temperature button, spin speed button, option buttons (Pre-wash, Extra Rinse, Delay Start).

Programs: Cotton (20°C-90°C), Synthetic (30°C-60°C), Delicate (cold-40°C), Wool, Sport, Anti-Allergy, Drum Clean, Quick 30, Steam Refresh. Settings: Child lock (hold buttons 3 sec), volume control, factory reset.

Connecting Water & Drain

Water inlet: Two hoses (blue for cold, red for hot). Drain: Hose to standpipe or sink.

Ensure water taps are off before connecting hoses.
Use only supplied hoses; do not overtighten.
Drain hose height: 60-100 cm from floor.
Check for leaks after first connection.

Tip: Install drain hose securely to avoid slipping during spin cycle.

Using Washing Programs

Select program based on fabric type and soil level.

Load laundry: Do not exceed 9 kg; distribute evenly.
Add detergent: Use compartments I (pre-wash), II (main wash), * (softener).
Select program: Turn dial (e.g., Cotton).
Adjust options: Temperature, spin speed, extra rinse if needed.
Start: Press START/PAUSE; door locks automatically.
Pause: Press START/PAUSE to stop; door unlocks after 2 minutes if water level is low.
End of cycle: Signal sounds; door unlocks; remove laundry promptly.

WARNING! Do not open door during high-temperature cycles; wait for cool-down.

Special Functions

Steam Refresh: 20-minute cycle to refresh clothes without detergent. Anti-Allergy: Heats to 60°C+ to eliminate allergens. Delay Start: Set start time up to 24 hours. Direct Spray: Continuously sprays drum for improved wash performance.

Care & Cleaning

Monthly maintenance: Clean detergent drawer, door seal, and run Drum Clean cycle.

Detergent drawer: Remove and rinse under warm water.
Door seal: Wipe with damp cloth; remove debris.
Drum clean: Use dedicated program or 90°C cotton cycle without laundry.
Filter: Clean drain filter every 3 months (see troubleshooting).

CAUTION! Unplug before cleaning. Do not use abrasive cleaners.

Regulatory Information

CE compliant. Meets EU Ecodesign and energy labeling regulations. Waste disposal: Follow local regulations for recycling. Manufacturer: Hotpoint, a Haier company. For support, visit www.hotpoint.eu or contact customer service at +44 (0) 344 561 1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Door not closed/power	Close door firmly; check plug and power outlet; enable child lock off.
No water intake	Taps closed/hose kink	Open water taps; check hose for kinks; clean inlet filter.
Water doesn't drain	Drain clogged/filter	Clean drain filter; ensure drain hose is not too low or kinked.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; re-level machine; redistribute load.
Error codes (e.g., F01)	Various faults	Consult manual error code list; unplug for 5 minutes, restart.

Reset: Unplug for 5 minutes, or hold START + POWER for 10 seconds.

Service: +44 (0) 344 561 1234; www.hotpoint.eu/support