Hotpoint Washing Machine SWMD9437 Manual

The Hotpoint SWMD9437 is a 9kg capacity front-loading washing machine with energy rating A+++, 1400 RPM spin speed, multiple wash programs including Eco, Cotton, Synthetic, Delicates, Quick Wash, and Steam Refresh. Features include digital display, delay start, child lock, anti-crease, and anti-allergy cycles. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Programs 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Front-loading drum, Digital control panel, Detergent drawer, Water inlet valves, Drain pump filter, Adjustable feet, Power cord.

Feature	Description
Capacity	9kg maximum load
Spin Speed	Up to 1400 RPM
Energy Rating	A+++ (most efficient)
Display	Digital LED with time remaining
Programs	14 programs including Eco 40-60, Cotton, Quick 30
Delay Start	Up to 24 hours
Child Lock	Prevents accidental program changes
Anti-Crease	Reduces wrinkles at end of cycle
Steam Refresh	Refreshes clothes without washing
Noise Level	Wash: 53 dB, Spin: 75 dB

Installation

Unpack and remove transit bolts. Place on level floor.

Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
Level the machine: Adjust front feet using wrench; use spirit level.
Connect water supply: Attach inlet hoses to hot/cold taps (if applicable).
Connect drain hose: Secure to standpipe or sink; use U-bend if needed.
Plug into grounded power outlet.

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use.

First-Time Setup

Power on machine; run initial empty wash.

Connect water and power: Ensure taps are open and outlet is live.
Add detergent: Pour 100ml of detergent into drawer II (main wash).
Select program: Turn dial to "Cotton 90°C" without load.
Start cycle: Press Start/Pause; let complete to clean drum.
Set preferences: Use Settings button for beep volume, etc.

CAUTION! First wash may have residual water; this is normal.

Specifications

Model: SWMD9437
Capacity: 9kg (dry weight)
Dimensions (HxWxD): 85cm x 60cm x 60cm
Voltage/Frequency: 220-240V, 50Hz
Power Consumption: 0.89 kWh per cycle (Eco 40-60)
Water Consumption: 48 liters per cycle (Eco 40-60)
Spin Speed: 1400 RPM (adjustable)
Programs: 14 including Wool, Silk, Sportswear
Noise: 53 dB (wash), 75 dB (spin)
Weight: 70kg

Controls and Settings

Control Panel: Program dial, Display, Temperature button, Spin speed button, Start/Pause, Options (Delay, Pre-wash, Extra rinse).

Program Dial: Select from Eco 40-60, Cotton, Synthetic, Delicates, Quick 30, Wool, Silk, Sportswear, Jeans, Anti-allergy, Drum Clean, Rinse+Spin, Spin Only, Steam Refresh.

Settings Menu: Press and hold Temperature + Spin for 3 seconds to access: Buzzer volume (High/Low/Off), End of cycle signal (On/Off), Button lock (On/Off).

Connecting Water Supply

Cold fill only (unless model has hot fill). Use supplied hoses.

Turn off taps before connecting.
Screw hoses onto machine inlet valves (red for hot if applicable, blue for cold).
Connect other ends to taps; ensure washers are fitted.
Open taps fully; check for leaks.
For drain: Place hose in standpipe (max height 100cm) or use sink adapter.

Tip: Do not overtighten hoses; hand-tight plus half turn is sufficient.

Using Wash Programs

Supports various fabrics and soil levels.

Load clothes: Do not exceed 9kg; distribute evenly.
Add detergent: Use drawer I (pre-wash), II (main wash), III (fabric softener).
Select program: Turn dial to desired program.
Adjust options: Press Temperature to change (e.g., 30°C to 90°C); Spin to adjust speed.
Add options: Press Delay for 1-24h; Extra Rinse, Pre-wash if needed.
Start: Press Start/Pause; display shows time remaining.
Pause/change: Press Start/Pause to stop; wait 2 minutes to open door.
End of cycle: Buzzer sounds; remove clothes promptly to reduce creasing.

WARNING! Do not open door during high-temperature washes; wait for cool-down.

Maintenance Features

Drum Clean: Run monthly with detergent to prevent odors. Child Lock: Press and hold Start/Pause + Spin for 3 seconds to activate/deactivate. Anti-Crease: Automatically tumbles clothes periodically after cycle ends (default on).

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth. Clean detergent drawer monthly: Pull out, rinse under tap. Clean drain pump filter every 3 months: Open flap at bottom front, place bowl, unscrew filter, remove debris.

CAUTION! Do not use abrasive cleaners; keep control panel dry.

Regulatory Information

CE compliant; meets EU Ecodesign and Energy Label regulations. Waste electrical products must not be disposed of with household waste. Please recycle. For support, visit www.hotpoint.co.uk or contact 0344 822 4224.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power/door	Check plug is in; ensure door is closed properly; press Start/Pause.
No water intake	Taps/hoses	Ensure taps are open; check hoses for kinks; clean inlet filters.
Water not draining	Drain filter/pipe	Clean pump filter; check drain hose for blockages; ensure height < 100cm.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; re-level machine; redistribute load.
Error codes (e.g., F01)	Fault	Unplug for 5 minutes; replug. If persists, note code and call support.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 0344 822 4224; www.hotpoint.co.uk