Hotpoint washing machine RPD 10477D manual

The Hotpoint RPD 10477D is a freestanding washing machine with a 10kg capacity, featuring multiple wash programs, energy efficiency class A+++, spin speed up to 1400 rpm, delay timer, child lock, and anti-flood protection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Control panel with digital display, detergent dispenser, drum, water inlet valves, drain pump, and adjustable feet.

Installation

Unpack and remove transit bolts. Place on level floor.

1. Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
2. Level the machine: Adjust feet using wrench; use spirit level.
3. Connect water supply: Attach inlet hoses to cold water tap (blue marker) and hot if applicable (red marker).
4. Connect drain hose: Place in standpipe or sink; secure with hook.
5. Plug into grounded power outlet.

WARNING! Do not install in wet areas. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Power on machine; run initial empty wash.

1. Check connections: Ensure water taps are on and hoses secure.
2. Select first wash: Choose "Cotton 90°C" program without laundry.
3. Add detergent: Pour 100ml of detergent into drawer II (main wash).
4. Start cycle: Press Start/Pause; let complete to clean drum.
5. Set preferences: Use Settings button to adjust beep volume, etc.

CAUTION! Do not load laundry during first wash. Ensure packaging materials are removed.

Specifications

• Model: RPD 10477D
• Type: Freestanding front-load washer
• Capacity: 10kg
• Max Spin Speed: 1400 rpm
• Energy Class: A+++
• Water Consumption: Approx. 50 litres per cycle (cotton 60°C)
• Power Supply: 220-240V, 50Hz, 10A
• Noise Level: Wash: 53 dB, Spin: 73 dB
• Programs: 16 including Eco, Wool, Sport, Anti-Allergy
• Dimensions: 85 x 60 x 60 cm (HxWxD)
• Weight: 70kg

Controls and Settings

Control Panel: Power button, Program selector knob, Display, Temperature button, Spin speed button, Delay Start button, Start/Pause button, Options button.

Display Icons: Child Lock, Delay Start, Spin Speed, Temperature, Time Remaining, Door Locked.

Program Selection: Turn knob to desired program (e.g., Cotton, Synthetics, Delicates). Temperature: Press repeatedly to select 20°C-90°C or Cold. Spin Speed: Select 400-1400 rpm or Rinse Hold. Delay Start: Set 1-24 hours. Options: Extra Rinse, Pre-Wash, Quick Wash (if available for program). Child Lock: Press and hold Temp + Spin for 3 seconds.

Connecting Water & Drain

Water Inlet: Two hoses (blue=cold, red=hot). Drain: Hose to standpipe or sink.

1. Turn off machine and water taps.
2. Connect hoses: Screw inlet hoses to taps; hand-tighten plus half turn with pliers.
3. Connect to machine: Attach hoses to corresponding valves at rear.
4. Drain hose: Insert into standpipe (max height 100cm) or over sink edge; secure.
5. Check for leaks: Turn on taps; inspect connections before first use.

Tip: Use new hoses; do not reuse old ones. Ensure drain hose is not kinked.

Using Wash Programs

Supports various fabrics and soil levels.

1. Load laundry: Open door, load evenly; do not overload.
2. Add detergent: Pour into drawer I (pre-wash), II (main wash), III (fabric softener).
3. Select program: Turn knob (e.g., Cotton for towels/bedding).
4. Adjust settings: Press Temp, Spin, Options as needed.
5. Delay Start: Press Delay button to set hours if desired.
6. Start: Press Start/Pause; door locks and cycle begins.
7. Pause/Stop: Press Start/Pause to pause; turn knob to Off to cancel.
8. End of cycle: Door unlocks; remove laundry promptly.

WARNING! Do not open door during wash; wait for unlock icon. Remove coins/objects from pockets.

Maintenance & Cleaning

Regular cleaning ensures performance and longevity.

1. Clean detergent drawer: Pull out, rinse under tap; wipe recess.
2. Clean door seal: Wipe rubber gasket to remove lint/debris.
3. Clean drum: Run "Drum Clean" program monthly (or Cotton 90°C empty).
4. Clean filter: Turn off machine; open filter cover at front bottom; place towel; unscrew filter cap slowly; clean under running water; reinsert.
5. Exterior: Wipe with damp cloth; do not use abrasive cleaners.

CAUTION! Unplug before cleaning filter. Do not use harsh chemicals.

Safety Features

Child Lock: Locks controls (press Temp + Spin 3 sec). Door Lock: Auto-locks during wash; unlocks at end. Anti-Flood: AquaStop shuts off water if leak detected. Overheat Protection: Thermostat prevents overheating. Imbalance Control: Auto-adjusts spin if load uneven.

Regulatory Information

CE marked; complies with EU directives for safety and EMC. Energy label according to EU regulation 2019/2014. Manufactured by Hotpoint, a brand of Whirlpool Corporation. For support, visit www.hotpoint.eu or contact 0800 316 1444 (UK).

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 0800 316 1444; www.hotpoint.eu