Hotpoint washing machine RD 1076 JD UK manual

The Hotpoint RD 1076 JD is a freestanding 7kg capacity washing machine designed for UK households, featuring multiple wash programmes, energy-efficient operation, a digital display, delay start, and child lock. It operates on a standard UK 220-240V, 50Hz power supply. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 7kg drum, Digital control panel, Programme selector, Delay timer, Child lock, Detergent dispenser, Filter access, Adjustable feet.

Installation

Unpack and remove all transit bolts and packaging. Place on a solid, level floor.

1. Connect water supply: Attach inlet hoses to cold water tap (and hot if applicable) using supplied connectors.
2. Connect drain hose: Place hose into standpipe or sink, ensuring it is secure and not kinked.
3. Level the machine: Adjust the feet using a spanner until the machine is stable and does not rock.
4. Plug into a grounded 3-pin socket (220-240V, 13A).

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure transit bolts are removed before first use to prevent damage.

First-Time Setup

After installation, run an empty wash cycle to clean the drum.

1. Power on the machine: Press the power button.
2. Select a cleaning cycle: Turn the programme selector to "Drum Clean" or a high-temperature cotton cycle (90°C).
3. Add detergent: Pour washing machine cleaner or a small amount of detergent into the main wash compartment.
4. Start the cycle: Press Start/Pause. Allow the cycle to complete.
5. Set preferences: Use the control buttons to adjust default spin speed, temperature, and other options as needed.

CAUTION! Ensure all packaging and transit bolts are removed. Check for water leaks during the first cycle.

Specifications

• Capacity: 7 kg (dry cotton).
• Dimensions (HxWxD): 85cm x 60cm x 60cm (approx).
• Energy Rating: A++ (EU scale).
• Spin Speed: Up to 1400 rpm.
• Programmes: Cotton, Synthetics, Delicates, Wool, Quick Wash, Drum Clean, etc.
• Water Pressure: Minimum 0.5 bar, Maximum 8 bar.
• Power Supply: 220-240V, 50Hz, 13A fuse.
• Noise Level: Wash: 56 dB(A), Spin: 76 dB(A).
• Door Opening: 180 degrees.

Controls and Settings

Control Panel: Power button, Programme selector dial, Digital display, Start/Pause button, Delay start button, Option buttons (Temperature, Spin Speed, Extra Rinse).

Programme Selection: Turn the dial to select the desired wash cycle. The default temperature and spin speed will illuminate; these can be changed using the option buttons before starting.

Option Buttons: Press to cycle through available settings (e.g., 30°C, 40°C, 60°C for temperature). A light indicates the selected option.

Delay Start: Press the delay button repeatedly to set start time (1-24 hours). The display will show the delayed start time.

Child Lock: Press and hold the Temperature and Spin Speed buttons simultaneously for 3 seconds to activate/deactivate. A padlock symbol will appear on the display.

Connecting Water & Drain

Water Inlet: Connect the blue hose to the cold water supply. If your model uses hot water, connect the red hose. Ensure taps are fully open. Drain: Secure the drain hose in a standpipe (minimum height 60cm, maximum 100cm from floor) or over the edge of a sink.

1. Turn off the water tap before connecting hoses.
2. Use only the supplied hoses; do not reuse old ones.
3. Ensure the drain hose is not pushed too far into the standpipe (max 15cm) to avoid siphoning.
4. Check for leaks at all connection points after the first cycle.

Tip: Install a drip tray or leak detector for added safety, especially on wooden floors.

Using Wash Programmes

Supports various fabrics and soil levels.

1. Load laundry: Open door, load items loosely without overfilling (max 7kg).
2. Add detergent: Open dispenser drawer, add powder/liquid to the correct compartments (I=pre-wash, II=main wash, * =fabric softener).
3. Select programme: Turn the dial (e.g., Cotton 60°C for towels).
4. Adjust options: Press Temperature or Spin Speed buttons if desired.
5. Start: Press Start/Pause. The door will lock and the cycle will begin.
6. Pause/Modify: Press Start/Pause to interrupt. You can add forgotten items if the water level is low and temperature is safe.
7. End of cycle: A buzzer will sound. The door remains locked until the "Door Locked" light goes out.

WARNING! Do not force the door open during a cycle. Check pockets for coins and objects that could damage the drum.

Special Features

Delay Start: Programme the machine to finish at a convenient time. Extra Rinse: Adds an additional rinse cycle for sensitive skin or heavy detergent use. Quick Wash: 30-minute cycle for small, lightly soiled loads. Drum Clean: Programme to run monthly (or as indicated) to prevent mould and odours.

Care & Cleaning

Unplug before cleaning. Wipe the exterior with a damp cloth. Clean the detergent dispenser monthly by pulling it out and rinsing under warm water. Clean the door seal regularly to remove lint and residue. Check and clean the pump filter every 3 months (see Troubleshooting for location). Run a Drum Clean cycle monthly with a dedicated cleaner or at 90°C.

CAUTION! Do not use abrasive cleaners, scouring pads, or solvents on the control panel or door. Keep the area around the filter dry.

Regulatory Information

This appliance complies with UK and EU safety standards. The CE mark indicates conformity with EEC directives. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. For service or warranty, contact Hotpoint UK: 03448 226 226 or visit www.hotpoint.co.uk. Model: RD 1076 JD. Serial number located on the door rim or rear panel.

Troubleshooting

Reset: Unplug the machine for 2 minutes, then reconnect. For persistent errors, contact Hotpoint service.

Service: 03448 226 226; www.hotpoint.co.uk