Hotpoint Washing Machine NSWM864CGGUKN Manual

The Hotpoint NSWM864CGGUKN is a freestanding 8kg capacity washing machine with an A+++ energy rating, 1400 RPM spin speed, AquaCare technology for fabric care, Direct Spray for efficient rinsing, Anti-Stain removal system, and multiple wash programs. It features a digital display, delay start, child lock, and quick wash options. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Utilities 7. Using Wash Programs 8. Special Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 8kg drum capacity, Digital display, Program selector knob, Start/Pause button, Delay start, Child lock, Anti-Stain system, AquaCare technology.

FeatureDescription
Capacity8kg (dry laundry weight)
Energy RatingA+++ (most efficient)
Spin SpeedUp to 1400 RPM
AquaCare TechnologyGentle on fabrics, reduces wear
Direct SprayEfficient rinsing system
Anti-Stain SystemTargets specific stains (wine, grass, etc.)
Digital DisplayShows time, program, settings
Delay StartSet wash to start later (up to 24h)
Child LockLocks controls during operation
Quick Wash30-minute program for lightly soiled loads

Installation

Unpack and remove transit bolts. Place on level floor.

  1. Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
  2. Connect water supply: Attach inlet hose to cold water tap (ensure washers are fitted).
  3. Connect drain hose: Place in standpipe or sink (use hook if provided).
  4. Level the machine: Adjust feet using spanner; use spirit level.
  5. Plug into AC power (230-240V, 50Hz).

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle.

  1. Connect power and water; turn on tap.
  2. Open detergent drawer; add 100g of detergent (no laundry).
  3. Select "Cotton 90°C" program; press Start.
  4. After cycle, machine is ready for normal use.

CAUTION! Ensure machine is level to prevent vibration. Check all connections for leaks.

Specifications

Controls and Settings

Control panel: Program selector knob, Digital display, Start/Pause, Delay start, Child lock, Option buttons.

Program Selection: Turn knob to desired program (Cotton, Synthetics, etc.). Display shows duration and settings.

Options: Press relevant button for Delay start (1-24h), Extra rinse, Pre-wash, Speed wash. Child lock: Hold for 3 seconds to activate/deactivate.

Settings: Temperature selection (cold to 90°C), Spin speed (400-1400 RPM or no spin), Load size (automatic or manual).

Connecting Utilities

Water: Cold fill only (inlet hose). Drain: Standpipe or sink. Power: 230-240V socket.

  1. Ensure water tap is off before connecting hose.
  2. Secure drain hose (max height 100cm).
  3. Use dedicated socket; avoid extension cords.

Tip: Check hose for kinks. Use flood prevention device if available.

Using Wash Programs

Select program based on fabric type and soil level.

  1. Load laundry: Do not exceed 8kg; distribute evenly.
  2. Add detergent: Use drawer compartments (I=pre-wash, II=main wash, * = softener).
  3. Select program: Turn knob (e.g., Cotton for cottons, Synthetics for blends).
  4. Set options: Temperature, spin speed, extra rinse if needed.
  5. Start: Press Start/Pause; display shows time remaining.
  6. Pause/change: Press Start/Pause to pause; turn knob to change program (drains first).
  7. End of cycle: Signal sounds; door unlocks after a few minutes.

WARNING! Do not open door during high-temperature washes; wait for cool down.

Special Features

Anti-Stain: Select program, then press Anti-Stain button; choose stain type (wine, grass, etc.). AquaCare: Automatically adjusts water usage for fabric care. Delay Start: Set start time (1-24h) for off-peak energy use. Quick Wash: 30-minute cycle for small, lightly soiled loads.

Care & Cleaning

Monthly maintenance: Clean detergent drawer, door seal, and filter.

  1. Detergent drawer: Pull out; wash under warm water.
  2. Door seal: Wipe with damp cloth; remove debris.
  3. Filter: Turn off machine; open filter cover (front bottom); place towel; unscrew filter; clean under running water.
  4. Run maintenance cycle: Use "Drum Clean" program or 90°C cotton cycle without laundry.

CAUTION! Unplug before cleaning filter. Do not use abrasive cleaners.

Regulatory Information

CE marked; complies with EU directives. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine won't startDoor not closed/powerEnsure door is shut; check power socket; press Start firmly.
No water intakeTap off/hose blockedTurn tap on; check hose for kinks; clean inlet filter.
Excessive vibrationTransit bolts/levelingEnsure transit bolts removed; adjust feet for level.
Water not drainingDrain hose blockedCheck hose for blockages; clean pump filter.
Error codes on displayVarious faultsConsult manual for code meaning (e.g., F01 = water inlet fault).

Reset: Unplug for 5 minutes; plug back in.

Service: 03448 113 113; www.hotpoint.co.uk

Hotpoint Washing Machine NSWM864CGGUKN Manual © - All Rights Reserved 2025