Hotpoint washing machine NSWM845CGGUKN manual

The Hotpoint NSWM845CGGUKN is a freestanding 8kg capacity washing machine with a 1400 RPM spin speed, featuring Hotpoint's Anti-Stain technology, Direct Spray pre-wash, and a wide range of automatic programmes. It includes energy-saving features, a large LED display, delay start, and child lock. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Washing Programmes 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 8kg drum, LED control panel, detergent dispenser, water inlet valves, drain pump, adjustable feet, and power cord.

FeatureDescription
Anti-Stain TechnologyAutomatically targets specific stains (wine, grass, mud, etc.)
Direct Spray Pre-WashSprays detergent directly onto clothes for improved stain removal
1400 RPM Spin SpeedHigh spin for reduced drying time
LED DisplayShows programme time, options, and status
Delay StartDelay washing up to 24 hours
Child LockLocks control panel to prevent accidental changes
Quick Wash30-minute programme for lightly soiled loads
Allergy CareExtra rinse and higher temperature to reduce allergens
Energy RatingA+++ for energy efficiency
Acoustic RatingLow noise levels during wash and spin

Installation

Unpack and remove all transit bolts and packaging. Place on a solid, level floor.

  1. Remove transit bolts: Use spanner to remove four bolts from rear; keep for future moves.
  2. Connect water supply: Attach inlet hoses to hot and cold taps (if applicable) and machine inlets (red for hot, blue for cold).
  3. Connect drain hose: Place into standpipe or sink; ensure no kinks and height between 60-100 cm.
  4. Level the machine: Adjust front feet to ensure machine is stable and does not rock.
  5. Plug into a grounded power outlet.

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, run a maintenance wash to clean the drum and remove any residues.

  1. Ensure machine is properly installed and levelled.
  2. Turn on water taps fully.
  3. Plug in and power on the machine.
  4. Run a 90°C cotton programme without laundry and with a small amount of detergent to clean the drum.
  5. Set your preferences: Use the control dial and buttons to set language, default spin speed, etc.

CAUTION! Never use the machine without removing all transit bolts. This can cause severe damage.

Specifications

Controls and Settings

Control Panel: Programme dial, Start/Pause button, Option buttons (Delay, Extra Rinse, etc.), LED display.

Programme Dial: Select from Cotton, Synthetics, Delicates, Wool, Quick Wash, Anti-Stain, Sports, Jeans, Allergy Care, Drum Clean.

Options: Delay Start (1-24 hrs), Extra Rinse, Reduced Creases, Pre-Wash, Speed Wash. Settings: Default spin speed adjustment, acoustic signal on/off, child lock activation. Display: Shows remaining time, selected options, and error codes.

Connecting Water & Drain

Water Inlet: Two hoses (blue for cold, red for hot). Drain: U-shaped hose end to prevent siphonage.

  1. Ensure both machine and taps are off before connecting.
  2. Screw hoses hand-tight, then a quarter turn with pliers (do not overtighten).
  3. Place drain hose in standpipe (min 60 cm, max 100 cm from floor) or over sink edge.
  4. Check for leaks by turning on taps briefly before first wash.

Tip: Use the drain hose support if supplied to secure hose in standpipe.

Using Washing Programmes

Supports various fabrics and soil levels.

  1. Sort laundry: Separate by colour and fabric type.
  2. Load machine: Do not exceed 8 kg; distribute evenly.
  3. Add detergent: Pour into correct dispenser compartment (I: pre-wash, II: main wash, *: softener).
  4. Select programme: Turn dial to desired programme (e.g., Cotton 60°C).
  5. Select options: Press buttons for Extra Rinse, Delay, etc.
  6. Start: Press Start/Pause; machine will fill, wash, rinse, and spin automatically.
  7. After cycle: Remove laundry promptly; leave door ajar to dry drum.

WARNING! Do not wash items contaminated with petrol, solvents, or chemicals. Risk of fire or explosion.

Special Functions

Anti-Stain: Select programme, machine automatically adjusts time/temp for selected stain type. Delay Start: Set 1-24 hours delay. Child Lock: Press and hold Delay and Extra Rinse for 3 seconds to lock/unlock controls. Drum Clean: Run monthly with detergent to prevent mould.

Care & Cleaning

Unplug before maintenance. Clean detergent dispenser monthly; wipe door seal and glass; run Drum Clean programme monthly.

CAUTION! Do not use abrasive cleaners or scouring pads on surfaces. Clean filter periodically to prevent blockages.

Regulatory Information

Complies with EU Ecodesign and Energy Labelling regulations. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine won't startDoor not closed/powerEnsure door is firmly shut; check power outlet and fuse.
No water intakeTaps off/hoses kinkedOpen taps fully; check hose for kinks; clean inlet filter.
Water leaksLoose connectionsTighten hose connections; check drain hose is secure.
Excessive vibration/noiseTransit bolts/uneven loadEnsure transit bolts removed; redistribute laundry; level feet.
Poor washing resultsDetergent/dosageUse correct detergent type and amount; select suitable programme.
Error code on displayVarious faultsConsult error code list in manual; try resetting by unplugging for 2 minutes.

Reset: Unplug for 2 minutes to reset electronic control.

Service: 03448 113 113; www.hotpoint.co.uk

Hotpoint washing machine NSWM845CGGUKN manual © - All Rights Reserved 2025