Hotpoint Washing Machine NSWM 943C W UK Manual

The Hotpoint NSWM 943C W is a 9kg capacity freestanding washing machine with an A+++ energy rating, featuring AquaCare technology for reduced water consumption, Direct Spray for efficient rinsing, a 1400 RPM spin speed, and a wide range of programs including Quick Wash, Eco, and Delicates. It includes a digital display, delay timer, child lock, and anti-flood protection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 9kg drum capacity, Digital Display, Program Selector Dial, Delay Start Button, Start/Pause Button, Child Lock, Anti-Flood System, AquaCare Technology.

Installation

Unpack and inspect contents. Place on a level, solid floor.

1. Remove transit bolts: Use spanner to remove all four bolts from rear; keep for future moves.
2. Connect water supply: Attach inlet hose to cold water tap (3/4” thread); ensure washers are fitted.
3. Connect drain hose: Place into standpipe or sink; secure with provided hook if needed.
4. Level the machine: Adjust front feet to ensure machine is stable and does not rock.
5. Plug into a grounded 230V AC power outlet.

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure transit bolts are removed before first use to prevent damage.

First-Time Setup

Power on the washing machine; perform initial setup.

1. Run a maintenance wash: Select the Drum Clean program (without laundry) to remove any residues.
2. Set language: If applicable via display settings (default is ENGLISH).
3. Test a wash cycle: Run a quick cycle with a small load to verify operation.
4. Familiarize with controls: Review program dial and button functions.

CAUTION! Ensure the machine is level to prevent excessive vibration during spin cycles.

Specifications

• Capacity: 9 kg (cotton).
• Energy Rating: A+++ (EU 2019/2014).
• Water Consumption: Approx. 45 litres per cycle (Eco 40-60).
• Spin Speed: Up to 1400 RPM.
• Noise Level: 74 dB (washing), 79 dB (spinning).
• Dimensions (HxWxD): 850 x 600 x 590 mm.
• Weight: 68 kg.
• Power Supply: 230V AC, 50Hz, 10A.
• Programs: Cotton, Synthetic, Delicates, Wool, Quick Wash, Eco, Drum Clean, etc.

Controls and Settings

Access settings via the Program Selector Dial and digital display buttons.

Control Panel: POWER Button, Program Dial, Start/Pause, Delay Start, Child Lock, Option Buttons (Extra Rinse, Pre-Wash, etc.).

Program Selection: Turn dial to desired program (e.g., Cotton, Eco, Quick Wash). Options: Adjust temperature, spin speed, and extra functions via corresponding buttons. Delay Start: Press to set start time (1-24 hours). Child Lock: Press and hold for 3 seconds to activate/deactivate. Display: Shows time remaining, selected options, and error codes.

Connecting Water & Drain

Water Inlet: Cold fill only (hose supplied). Drain: Hose to standpipe or sink.

1. Ensure water tap is off before connecting inlet hose.
2. Connect hose to machine first, then to tap; hand-tighten only.
3. Place drain hose securely into standpipe (height between 60-100 cm from floor).
4. Check for leaks by turning on tap briefly before first wash.

Tip: Do not kink or stretch hoses. Use only the supplied hoses.

Using Washing Programs

Supports various fabrics and soil levels.

1. Load laundry: Open door, load items loosely without overfilling.
2. Add detergent: Pour into detergent drawer (main wash and pre-wash compartments as needed).
3. Select program: Turn dial (e.g., Cotton for normal loads, Eco for energy saving).
4. Adjust options: Set temperature, spin speed, and extra functions if desired.
5. Start cycle: Press Start/Pause; display will show time remaining.
6. Pause/change: Press Start/Pause to pause; turn dial to change program (when paused).
7. End of cycle: Machine beeps; remove laundry promptly to avoid creasing.

WARNING! Do not open door during high-temperature washes or spin cycle. Wait for door lock indicator to go off.

Special Features

Child Lock: Prevents accidental program changes. Delay Start: Schedule wash to finish at a convenient time. Anti-Flood: Automatically stops water intake if a leak is detected. Drum Clean: Program to clean drum and prevent odors (run monthly).

Care & Cleaning

Unplug before cleaning. Wipe exterior with a damp cloth. Clean detergent drawer and door seal regularly to prevent mold.

Monthly Maintenance: Run Drum Clean program (without laundry). Clean filter (located behind lower access panel) to remove debris.

CAUTION! Do not use abrasive cleaners or solvents. Keep the area around the machine dry.

Regulatory Information

CE Marked: Complies with EU safety, health, and environmental requirements. Waste Electrical and Electronic Equipment (WEEE): Do not dispose with household waste; recycle appropriately. For support, visit www.hotpoint.co.uk or contact 03448 226 226 (UK).

Troubleshooting

Reset: Unplug for 2 minutes, then reconnect to reset electronic control.

Service: 03448 226 226 (UK); www.hotpoint.co.uk