Hotpoint washing machine NSWF 743U W UK manual

The Hotpoint NSWF 743U W is a 7kg capacity freestanding washing machine with A+++ energy rating, 1400 RPM spin speed, and multiple wash programs. It features direct spray technology for efficient washing, delay start, quick wash options, child lock, and anti-flood protection. Designed for UK households, it operates on 220-240V, 50Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Programs 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 7kg drum, electronic control panel, detergent drawer, water inlet valves, drain pump, adjustable feet, and power cord.

Feature	Description
Direct Spray Technology	Sprays water directly onto laundry for better detergent dissolution
1400 RPM Spin Speed	High spin reduces drying time
A+++ Energy Rating	Most efficient energy class
Quick Wash 30'	30-minute cycle for lightly soiled loads
Delay Start	Delay washing up to 24 hours
Child Lock	Locks controls during operation
Anti-Flood Protection	Automatic water shut-off in case of leak detection
Detergent Drawer	Compartments for pre-wash, main wash, and fabric softener
Adjustable Feet	For levelling on uneven floors
Digital Display	Shows time remaining, cycle stage, and error codes

Installation

Unpack and inspect contents. Place on stable, level floor near water and drain points.

Remove transit bolts: Use spanner to remove four bolts at rear; keep for future moves.
Connect water supply: Attach inlet hose to cold water tap (3/4” thread); ensure washers are fitted.
Connect drain hose: Place into standpipe or sink; secure with hook if provided.
Level the machine: Adjust feet clockwise/counter-clockwise; use spirit level.
Plug into grounded power socket.

WARNING! Do not use extension cords. Ensure water connections are tight to prevent leaks.

First-Time Setup

Power on machine; run initial empty wash cycle.

Set language: Press and hold PROGRAM and OPTION buttons for 3 seconds to select English.
Run cleaning cycle: Select “Drum Clean” program (if available) or a 90°C cotton cycle without laundry.
Load detergent: Add 100ml of detergent to drawer compartment II.
Start cycle: Press START/PAUSE; let complete to remove manufacturing residues.

CAUTION! Ensure transit bolts are removed before first use to prevent damage.

Specifications

Capacity: 7kg (cotton).
Energy Rating: A+++ (scale A+++ to D).
Spin Speed: Up to 1400 RPM.
Water Pressure: 0.5-10 bar.
Programs: Cotton, Synthetic, Delicates, Wool, Quick Wash, Drum Clean, etc.
Dimensions (HxWxD): 85 x 60 x 60 cm.
Power Supply: 220-240V, 50Hz.
Noise Level: 53 dB (washing), 75 dB (spinning).
Weight: 68 kg.

Controls and Settings

Control Panel: POWER, PROGRAM selector, OPTION buttons, START/PAUSE, CHILD LOCK.

Programs: Cotton (20°C-90°C), Synthetic (30°C-60°C), Delicates (cold-40°C), Wool, Quick Wash 30’, Drum Clean. Options: Extra Rinse, Pre-Wash, Delay Start, Speed Wash. Settings: Temperature selection, spin speed reduction, child lock activation.

Detergent Drawer: I-Pre-wash, II-Main wash, III-Fabric softener. Display: Shows cycle time, temperature, spin speed, and error codes (e.g., F01, F05).

Connecting Water & Drain

Water Inlet: Cold fill only (hose supplied). Drain: Hose to standpipe (max height 1m).

Turn off water tap before connecting hose.
Connect hose to machine first, then to tap; tighten by hand plus half turn with pliers.
Place drain hose into standpipe (min diameter 4cm) or over sink edge; secure with hook.
Check for leaks by turning on tap briefly before starting machine.

Tip: Do not kink or bend hoses sharply.

Using Wash Programs

Select program based on fabric type and soil level.

Load laundry: Do not exceed 7kg; distribute evenly.
Add detergent: Use drawer compartments I/II; follow dosage instructions.
Select options: Press OPTION buttons (e.g., Extra Rinse).
Start: Press START/PAUSE; display shows time remaining.
Pause/change: Press START/PAUSE to pause; turn knob to change program (if allowed).
End of cycle: Machine beeps; door unlocks after a short delay.

WARNING! Do not open door during spin cycle. Wait for drum to stop completely.

Special Functions

Delay Start: Set delay (1-24 hours) before wash begins. Child Lock: Press and hold CHILD LOCK for 3 seconds to lock/unlock controls. Anti-Crease: Keeps laundry tumbling after cycle end to reduce wrinkles. Drum Clean: Runs high-temperature cycle to clean drum; use monthly.

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth; clean detergent drawer monthly; run Drum Clean program regularly.

CAUTION! Do not use abrasive cleaners or solvents. Clean filter every 3 months to prevent blockages.

Regulatory Information

Complies with UK Electrical Equipment Safety Regulations 2016, WEEE Directive. CE marked. Energy label according to EU Regulation 2019/2014. Manufactured for Hotpoint, a Haier company. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Door not closed/power	Close door firmly; check plug socket; ensure child lock is off.
No water intake	Tap off/hose kinked	Open tap; straighten hose; check water pressure.
Water doesn't drain	Drain blocked/filter clogged	Clean pump filter; ensure drain hose is not too high.
Excessive vibration	Transit bolts not removed/uneven floor	Remove transit bolts; re-level machine; redistribute load.
Error code F05	Heater fault	Unplug for 5 minutes; restart. If persists, call service.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 03448 113 113; www.hotpoint.co.uk