Hotpoint washing machine NSWF 743U BS UK manual

The Hotpoint NSWF 743U BS is a freestanding 7kg capacity washing machine with an A+++ energy rating, featuring 1400 RPM spin speed, multiple wash programmes including Eco 40-60, Quick Wash, and Delicates, a delay timer up to 24 hours, child lock, and anti-flood protection. Designed for UK households, it operates on 220-240V, 50Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 7kg drum, LED display, programme selector knob, detergent dispenser, filter access, water inlet hoses, drain hose.

Installation

Unpack and remove transit bolts. Place on level, solid floor.

1. Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
2. Connect water supply: Attach inlet hoses to cold water tap (blue marker) and machine inlet.
3. Connect drain hose: Place in standpipe or sink (max height 100cm).
4. Level the machine: Adjust front feet to ensure stability; use spirit level.
5. Plug into grounded 3-pin socket.

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle.

1. Power on: Plug in and press power button.
2. Run empty drum clean: Select "Drum Clean" programme (if available) or a 90°C cotton cycle without laundry.
3. Set preferences: Use settings button to adjust buzzer volume, etc.
4. Load detergent: Fill detergent dispenser compartments as per instructions.

CAUTION! Ensure all packaging and transit bolts are removed. Check for water leaks after first connection.

Specifications

• Model: NSWF 743U BS UK
• Capacity: 7kg
• Dimensions (HxWxD): 85cm x 60cm x 60cm
• Energy Rating: A+++
• Annual Energy Consumption: 150 kWh
• Water Consumption: 45 litres per cycle (Eco 40-60)
• Spin Speed: 1400 RPM (adjustable)
• Programmes: 14 including Eco 40-60, Cotton, Quick Wash, Delicates, Wool, Sport
• Noise: Wash 53 dB(A); Spin 75 dB(A)
• Supply Voltage: 220-240V, 50Hz
• Max Load Power: 2100W
• Inlet Water Pressure: 0.5 - 10 bar

Controls and Settings

Control Panel: Power button, Programme selector knob, Start/Pause button, Delay timer button, Option buttons (e.g., Extra Rinse, Pre-wash).

Programme Selection: Turn knob to desired programme (LED will indicate selection).

Options: Press relevant button to activate: Delay Start (1-24h), Extra Rinse, Pre-wash, Reduced Creases, Speed Wash.

Child Lock: Press and hold Delay + Option buttons for 3 seconds to enable/disable.

Display: Shows time remaining, cycle stage, and selected options.

Connecting Water & Drainage

Cold water fill only. Ensure hoses are not kinked.

1. Connect inlet hose: Screw blue-marked hose to cold water tap; other end to machine inlet (marked "C").
2. Connect drain hose: Insert into standpipe (min diameter 4cm) or secure over sink edge.
3. Check for leaks: Turn on tap and inspect connections before first use.

Tip: Use only supplied hoses; do not extend or repair. Drain hose must not be higher than 100cm from floor.

Using Wash Programmes

Select programme based on fabric type and soil level.

1. Load laundry: Do not exceed 7kg; distribute evenly.
2. Add detergent: Use compartment I (pre-wash), II (main wash), * (fabric softener).
3. Select programme: Turn knob (e.g., Cotton 40°C for everyday items).
4. Select options: Press buttons for Extra Rinse, Delay, etc.
5. Start: Press Start/Pause; machine will lock door and begin cycle.
6. Pause/Stop: Press Start/Pause to pause; turn knob to "Stop" to cancel.
7. End of cycle: Buzzer sounds; door unlocks after a short delay.

WARNING! Do not open door during high-temperature cycles. Remove items promptly after cycle to prevent creasing.

Safety Features

Child Lock: Locks control panel during operation. Door Lock: Automatically locks during wash; unlocks at end. Anti-Flood: AquaStop™ shuts off water if leak detected. Overheating Protection: Thermal cut-out prevents motor overheating.

Care & Cleaning

Regular maintenance ensures optimal performance.

1. Clean detergent drawer: Remove and rinse under warm water monthly.
2. Clean filter: Turn off machine; open filter cover at front bottom; place towel; unscrew filter cap slowly to drain residual water; clean filter; reinsert.
3. Clean drum: Run empty 90°C cotton cycle monthly or use dedicated drum clean programme.
4. Wipe exterior: Use damp cloth; do not use abrasive cleaners.

CAUTION! Unplug before cleaning filter. Do not use steam cleaners.

Regulatory Information

Complies with UK Electrical Equipment (Safety) Regulations 2016, EC Directive 2009/125/EC (ErP), and WEEE Regulations. Energy label according to EU Regulation 2019/2014. Manufacturer: Hotpoint, Peterborough, UK. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 03448 113 113; www.hotpoint.co.uk