Hotpoint washing machine NSWA 845C WW UK N manual

The Hotpoint NSWA 845C WW UK N is a freestanding washing machine with an 8kg capacity, 1400 RPM spin speed, A+++ energy rating, and multiple wash programs. It features electronic controls, a digital display, delay start, child lock, and anti-flood protection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Programs 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Electronic control panel, detergent dispenser, drum, door with safety lock, water inlet valves, drain pump, adjustable feet.

FeatureDescription
Capacity8kg (dry laundry)
Spin SpeedUp to 1400 RPM
Energy RatingA+++ (most efficient)
Programs15+ programs including Cotton, Synthetics, Delicates, Quick Wash
DisplayDigital display with time remaining, cycle stage
Delay StartUp to 24 hours
Child LockPrevents accidental program changes
Anti-Flood ProtectionAquaStop technology
Door LockAutomatic safety lock during operation
Adjustable FeetFor leveling on uneven floors

Installation

Unpack and remove transit bolts. Place on stable, level floor.

  1. Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
  2. Connect water supply: Attach inlet hose to cold water tap (3/4" thread). Ensure washers are fitted.
  3. Connect drain hose: Place into standpipe or sink; secure with hook if provided.
  4. Level the machine: Adjust front feet using spanner until machine is stable.
  5. Plug into grounded power outlet.

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle.

  1. Power on machine: Press POWER button.
  2. Run cleaning cycle: Select "Drum Clean" or "Maintenance" program (without laundry).
  3. Set preferences: Use SETTINGS button to set time, beep volume, etc.
  4. Load detergent: Fill compartments as per detergent manufacturer's instructions.

CAUTION! Ensure all packaging and protective films are removed from drum and door seal.

Specifications

Controls and Settings

Control Panel: POWER, PROGRAM SELECTOR knob, START/PAUSE, OPTIONS buttons, DISPLAY.

Display Icons: Time remaining, child lock, delay start, temperature, spin speed, door locked.

Program Selection: Turn knob to desired program. Options: Temperature (cold-90°C), Spin Speed (0-1400 RPM), Delay Start (1-24h), Extra Rinse, Pre-Wash. Settings Menu: Press and hold SETTINGS to access time setting, beep volume, end of cycle signal.

Connecting Water & Drain

Water Inlet: Cold water only (unless model specifies hot). Drain: To standpipe or sink.

  1. Ensure water tap is off before connecting hose.
  2. Connect inlet hose to tap; hand-tighten, then quarter turn with pliers.
  3. Place drain hose in standpipe (60-100cm height) or secure over sink edge.
  4. Check for leaks by turning on tap briefly before first use.

Tip: Do not kink or bend hoses. Use original hoses only.

Using Wash Programs

Select program based on fabric type and soil level.

  1. Load laundry: Do not overload; distribute evenly.
  2. Add detergent: Use compartments I (pre-wash), II (main wash), * (softener).
  3. Select program: Turn knob (e.g., Cotton 40°C).
  4. Adjust options: Press TEMP, SPIN, etc., to modify.
  5. Start: Press START/PAUSE; door locks automatically.
  6. Pause/Stop: Press START/PAUSE to pause; turn knob to reset.
  7. After cycle: Door unlocks; remove laundry promptly.

WARNING! Do not open door during wash/spin; wait for unlock signal.

Special Functions

Delay Start: Set 1-24h delay; machine starts automatically. Child Lock: Press and hold CHILD LOCK for 3 seconds; locks controls. Anti-Crease: Tumbles intermittently after cycle to reduce wrinkles. Extra Rinse: Adds rinse cycle for sensitive skin. Quick Wash: 30-minute cycle for lightly soiled loads.

Care & Cleaning

Monthly maintenance: Clean detergent drawer, door seal, and drum.

  1. Detergent drawer: Remove and rinse under warm water.
  2. Door seal: Wipe with damp cloth; check for objects.
  3. Drum: Run "Drum Clean" program empty at 90°C.
  4. Filter: Clean drain pump filter every 2-3 months (see manual).

CAUTION! Unplug before cleaning. Do not use abrasive cleaners.

Regulatory Information

CE marked; complies with EU directives for safety and EMC. Energy label according to EU regulation 2019/2014. Waste electrical products must not be disposed of with household waste. Please recycle. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine won't startDoor not closed/powerClose door firmly; check plug/power; press START.
No water intakeTap off/hose kinkedOpen tap; straighten hose; check filter.
Water doesn't drainDrain blocked/filterClean pump filter; check drain hose for blockages.
Excessive vibrationTransit bolts/levelingEnsure transit bolts removed; re-level machine.
Error codes (E01-E10)Various faultsRefer to manual; common: E02 (door issue), E10 (motor fault).

Reset: Unplug for 1 minute, then restart.

Service: 03448 113 113; www.hotpoint.co.uk

Hotpoint washing machine NSWA 845C WW UK N manual © - All Rights Reserved 2025