Hotpoint Washing Machine NSWA 1043C WW UK Manual

The Hotpoint NSWA 1043C WW is a freestanding 10kg capacity washing machine with an A+++ energy rating, 1400 RPM spin speed, and multiple wash programs. It features Hotpoint's Anti-Stain technology, a delay timer, child lock, and a large LED display. Designed for UK households, it operates on 220-240V, 50Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Utilities 7. Using Wash Programs 8. Special Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 10kg drum, LED control panel, detergent dispenser, filter, drain hose, water inlet valves.

Feature	Description
Capacity	10kg (cotton)
Energy Rating	A+++
Spin Speed	Up to 1400 RPM
Anti-Stain Technology	Automatic stain removal for common stains
Programs	15 programs including Cotton, Synthetic, Delicates, Quick Wash
Delay Timer	Up to 24 hours
Child Lock	Prevents accidental program changes
Display	LED with time remaining indicator
Door	Reversible (opens left or right)
Dimensions (HxWxD)	850 x 600 x 600 mm

Installation

Unpack and remove transit bolts. Place on level floor.

Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
Connect water supply: Attach inlet hose to cold water tap (3/4”); ensure washers are fitted.
Connect drain hose: Place in standpipe or sink (max height 100cm).
Level the machine: Adjust front feet; use spirit level.
Plug into 220-240V, 50Hz socket (with earth).

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use.

First-Time Setup

Before first wash, run a maintenance cycle.

Connect power and water; turn on tap fully.
Open detergent dispenser; pour 1 litre of water into compartment II (softener) to activate.
Select "Cotton 90°C" program without laundry.
Add half a measure of detergent to drum.
Start cycle to clean drum and remove residues.
Set language if applicable (default English).

CAUTION! Ensure machine is level to prevent vibration and noise.

Specifications

Model: NSWA 1043C WW
Capacity: 10kg
Energy Class: A+++
Annual Energy Consumption: 175 kWh
Water Consumption: 10,200 litres/year
Spin Speed: 1400 RPM (max)
Noise Level (wash/spin): 56/76 dB(A)
Programs: 15 including Eco 40-60, Wool, Sport, Anti-Stain
Dimensions: 850 x 600 x 600 mm (HxWxD)
Weight: 70 kg
Power Supply: 220-240V, 50Hz
Max Pressure: 1 MPa (10 bar)
Min Pressure: 0.05 MPa (0.5 bar)

Controls and Settings

Control Panel: POWER button, Program selector dial, Start/Pause, Delay Timer, Extra Rinse, Speed/Spin reduction, Child Lock.

Program Dial: Select from 15 programs (Cotton, Synthetic, Delicates, Quick 30’, Wool, Silk, Sport, Jeans, Anti-Stain, Eco 40-60, etc.).

Options: Delay Timer (1-24h), Extra Rinse (adds rinse cycle), Speed Reduction (lower spin speed). Child Lock: Press and hold Delay + Extra Rinse for 3 seconds (icon lights). Display: Shows time remaining, cycle stage, and options.

Connecting Utilities

Water: Cold fill only. Drain: Standpipe or sink.

Ensure water tap is off before connecting hose.
Use only provided inlet hose; do not lengthen.
Drain hose must not be kinked; secure in standpipe (max 100cm height).
Plug into grounded socket; avoid extension cords.

Tip: Check for leaks after first connection.

Using Wash Programs

Select program based on fabric type and soil level.

Load laundry: Do not exceed 10kg; distribute evenly.
Add detergent: Use compartment I (main wash) for powder; II for softener; III for pre-wash.
Select program: Turn dial (e.g., Cotton for cottons).
Set options: Delay, Extra Rinse, Spin Speed as needed.
Start: Press Start/Pause; door locks automatically.
Pause/change: Press Start/Pause to pause; turn dial to change program (if door unlocked).
End of cycle: Signal sounds; door unlocks after a few minutes.

WARNING! Do not open door during wash; wait until unlocked.

Special Functions

Anti-Stain: Select Anti-Stain program for automatic treatment of wine, grass, mud, etc. Delay Timer: Set wash to finish up to 24 hours later. Child Lock: Prevents accidental button presses. Extra Rinse: Adds rinse for sensitive skin or heavy detergent.

Care & Cleaning

Monthly maintenance:

Clean detergent drawer: Remove and rinse under tap.
Clean drum: Run "Drum Clean" program or Cotton 90°C without laundry.
Clean filter: Turn off machine; open filter cover at front bottom; place towel; unscrew filter cap slowly; clean under water.
Wipe door seal and glass to remove lint.

CAUTION! Unplug before cleaning filter. Do not use abrasive cleaners.

Regulatory Information

Complies with UK Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility Regulations 2016. CE marked. Manufacturer: Hotpoint, a Haier company. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Door not closed/power	Close door firmly; check plug and socket; ensure child lock is off.
No water intake	Tap off/hose kinked	Open tap fully; check hose for kinks; clean inlet filter.
Water leaks	Hose connections	Tighten inlet/drain hoses; check detergent drawer is seated.
Excessive vibration/noise	Transit bolts/leveling	Ensure transit bolts removed; check machine is level; redistribute load.
Poor wash results	Detergent/overload	Use correct detergent amount; do not overload; select proper program.
Door won't open	Water in drum/safety lock	Wait a few minutes; start drain/spin program; unplug for 2 minutes.
Error codes (e.g., F01, F02)	Faults	Consult manual; common: F01 (drain issue), F02 (water intake fault).

Reset: Unplug for 2 minutes, then restart.

Service: 03448 113 113; www.hotpoint.co.uk