Hotpoint washing machine NLLCD 1046 WD AW UK N manual

The Hotpoint NLLCD 1046 WD AW UK N is a freestanding washing machine with a 10kg capacity, 1400 RPM spin speed, A+++ energy rating, and multiple wash programs. It features AquaCare technology for reduced water consumption, Direct Spray for efficient rinsing, Anti-Stain removal, and a delay timer. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Control panel with rotary selector and digital display, detergent drawer, drum, water inlet valves, drain pump, and adjustable feet.

Installation

Unpack and remove all transit bolts and packaging. Place on a solid, level floor.

1. Connect water supply: Attach inlet hoses to cold water tap (and hot if applicable) using supplied connectors.
2. Connect drain hose: Place hose into standpipe or sink, ensuring it is secure and not kinked.
3. Level the machine: Adjust the four feet using a spanner to ensure stability.
4. Plug into a grounded 220-240V AC power outlet.

WARNING! Do not remove transit bolts before moving to final location. Ensure water connections are tight to prevent leaks.

First-Time Setup

After installation, run an initial empty wash cycle to clean the drum.

1. Remove transit bolts completely and store safely.
2. Connect power and turn on the machine.
3. Select the "Drum Clean" or "Cotton 90°C" program without laundry.
4. Add a small amount of detergent to the main wash compartment.
5. Press Start/Pause to begin the cycle.

CAUTION! Ensure all packaging and transit bolts are removed before first use to prevent damage and excessive vibration.

Specifications

• Model: NLLCD 1046 WD AW UK N
• Type: Freestanding Front Loader
• Capacity: 10kg
• Max Spin Speed: 1400 RPM
• Energy Class: A+++
• Water Consumption: Approx. 50 litres per cycle (Eco 40-60)
• Noise Level (wash/spin): 53dB / 74dB
• Dimensions (HxWxD): 85cm x 60cm x 60cm
• Programs: Cotton, Synthetic, Delicates, Wool, Quick Wash, Anti-Stain, Drum Clean
• Power Supply: 220-240V, 50Hz

Controls and Settings

Access programs and settings via the rotary dial and button panel.

Control Panel: Rotary Program Selector, Start/Pause button, Delay Timer button, Option buttons (e.g., Extra Rinse, Pre Wash), Digital Display, Child Lock button.

Program Selection: Turn dial to desired program (Cotton, Eco 40-60, Synthetic, etc.). Options: Select additional functions like Extra Rinse or Reduced Crease. Delay Timer: Set wash start delay from 1 to 24 hours. Temperature/Spin: Adjustable for most programs via corresponding buttons. Child Lock: Press and hold specific buttons to lock/unlock controls.

Connecting Water & Drain

Cold water inlet (mandatory), optional hot water inlet. Drain hose for expulsion.

1. Ensure water supply taps are off before connecting hoses.
2. Connect the inlet hoses to the corresponding valves on the machine (blue for cold, red for hot if used).
3. Connect the other ends to the water taps, ensuring seals are in place.
4. Place drain hose into a standpipe (min. 60cm height) or over the edge of a sink.
5. Secure the hose to prevent slipping.

Tip: Do not extend the drain hose beyond 1.5m. Avoid sharp bends.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Open door, load items loosely without overfilling.
2. Add detergent: Pour into main wash compartment (II) of the drawer. Use pre-wash compartment (I) if selected.
3. Select program: Turn dial to desired program (e.g., Cotton 40°C).
4. Set options: Press buttons for Extra Rinse, Reduced Spin, etc.
5. Start: Press Start/Pause. The display will show time remaining.
6. At end of cycle: A tone sounds. Remove laundry promptly to avoid creasing.

WARNING! Do not wash items soiled with flammable substances. Balance the load to reduce vibration.

Special Functions

Delay Timer: Delays start of wash cycle. Child Lock: Locks controls to prevent changes. Anti-Stain: Targets specific stains (grass, wine, grease). Quick Wash: 30-minute cycle for lightly soiled items. Reduced Crease: Gentle final spin and tumble to minimise wrinkles.

Care & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Clean detergent drawer: Pull out, rinse under warm water, and dry before replacing.
2. Clean door seal: Wipe rubber gasket with a damp cloth to remove lint and residue.
3. Clean filter: Locate filter behind the small hatch at the bottom front. Place a towel, unscrew slowly to drain residual water, clean under running water, and refit.
4. Run Drum Clean program: Monthly, without laundry, to clean the drum and internal system.

CAUTION! Unplug the machine before cleaning the filter. Do not use abrasive cleaners.

Regulatory Information

Complies with EU Ecodesign and Energy Labelling regulations. Waste electrical products should not be disposed of with household waste. Please recycle according to local regulations. Manufactured for the UK market. For support, visit www.hotpoint.co.uk or contact 0333 305 2265.

Troubleshooting

Reset: Unplug for 2 minutes, then reconnect. For persistent errors, call support.

Service: 0333 305 2265; www.hotpoint.co.uk