Hotpoint washing machine NLCD 1164 D AW UK N manual

The Hotpoint NLCD 1164 D AW UK N is a freestanding washing machine with a 6kg load capacity, A+++ energy rating, 1400 rpm spin speed, and multiple wash programs. It features electronic controls, a digital display, delay start, child lock, and various safety systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Electronic control panel, detergent dispenser, drum, door with safety lock, water inlet valves, drain pump, adjustable feet.

Installation

Unpack and remove all transit bolts and packaging. Place on a solid, level floor.

1. Remove transit bolts: Use spanner to remove the 4 bolts at the rear; keep bolts for future moves.
2. Level the machine: Adjust the front feet using a spanner until the machine is stable and does not rock.
3. Connect water supply: Attach the inlet hose (supplied) to a cold water tap (3/4" thread). Ensure the hose is not kinked.
4. Connect drain hose: Place the drain hose into a standpipe (min. height 60cm, max. 100cm) or over the edge of a sink.
5. Plug into a grounded electrical outlet (220-240V, 50Hz).

WARNING! Do not install in areas prone to freezing temperatures or direct sunlight. Ensure the power cord and hoses are not trapped or damaged.

First-Time Setup

Before first use, run a cotton cycle at 90°C without laundry to clean the drum and remove any residues.

1. Open the detergent dispenser and fill compartment II with a small amount of detergent (approx. 100ml).
2. Close the door and select the "Cotton 90°C" program.
3. Press the Start/Pause button. The cycle will run for approximately 2 hours.
4. After completion, the machine is ready for normal use.

CAUTION! The door will be locked during the cycle. Do not attempt to force it open.

Specifications

• Model: NLCD 1164 D AW UK N
• Type: Freestanding Front-Loading Washing Machine
• Capacity: 6 kg
• Energy Class: A+++
• Annual Energy Consumption: 150 kWh
• Water Consumption: 45 litres per cycle (Cotton 60°C)
• Spin Speed: 1400 rpm
• Noise Level (Wash/Spin): 56/76 dB(A)
• Dimensions (HxWxD): 85 x 60 x 60 cm
• Power Supply: 220-240V ~ 50Hz
• Max Load Power: 2100 W
• Programs: 14
• Colour: White

Controls and Settings

Control Panel: ON/OFF button, Program selector dial, Digital display, Temperature button, Spin speed button, Option buttons (Delay Start, Extra Rinse, etc.), Start/Pause button.

Program Dial: Turn to select the desired wash program (e.g., Cotton, Synthetics, Delicates, Wool, Quick 30'). The default temperature and spin speed for that program will illuminate.

Temperature Selection: Press the Temperature button repeatedly to cycle through available options (Cold, 30°C, 40°C, 60°C, 90°C). The selected temperature will flash.

Spin Speed Selection: Press the Spin Speed button to cycle through options (No Spin, 400, 600, 800, 1000, 1200, 1400 rpm).

Options: Use the respective buttons to activate Delay Start (1-24h), Extra Rinse, or Pre-Wash. The corresponding LED will light up.

Child Lock: Press and hold the Delay Start and Extra Rinse buttons simultaneously for 3 seconds to activate/deactivate. When active, all buttons except ON/OFF are locked.

Connecting Water & Drain

Ensure all connections are secure before first use.

1. Water Inlet: Connect the blue-marked hose to the cold water supply. Do not use with hot water.
2. Drain Hose: Secure the drain hose in a standpipe (internal diameter min. 38mm) at a height between 60cm and 100cm from the floor. Alternatively, use the U-shaped hook to hang it over a sink edge.
3. Check for Leaks: After connections, turn on the water tap and check both inlet and drain connections for any drips.

Tip: The drain hose should not be pushed more than 15cm into the standpipe to avoid siphoning.

Using Wash Programs

Select the program best suited to your laundry type and soil level.

1. Sort laundry: Separate by colour, fabric type, and care labels.
2. Load the drum: Do not overload. Items should move freely.
3. Add detergent: Open the dispenser drawer. Add powder/liquid detergent to compartment II (main wash). For pre-wash, use compartment I. Add fabric softener to compartment III (max. level marked).
4. Close door and select program: Turn the dial to the desired program.
5. Adjust settings: Modify temperature, spin speed, or add options if needed.
6. Start: Press the Start/Pause button. The door will lock, and the display will show the time remaining.
7. End of cycle: An audible signal will sound. The door lock symbol will go out after a few minutes. Unload promptly.

WARNING! Do not wash items soiled with flammable substances (petrol, oil, etc.). Remove coins, keys, etc. from pockets.

Special Functions

Delay Start: Allows you to set the wash cycle to finish at a desired time. Press the Delay button repeatedly to set the delay (1-24 hours). The delayed start time will be shown on the display.

Extra Rinse: Adds an additional rinse cycle, useful for sensitive skin or heavily soiled loads.

Pre-Wash: Select for very dirty loads. Requires adding detergent to compartment I of the dispenser.

Child Lock: Locks the control panel to prevent children from changing settings.

Care & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Clean the detergent dispenser: Pull out the drawer, press the release tab, and wash under running water.
2. Clean the door seal: Wipe the rubber gasket with a damp cloth to remove lint and residue. Leave the door ajar between washes to air the drum.
3. Clean the drain pump filter: In case of a blockage or to remove small objects, turn off and unplug the machine. Open the filter cover (bottom front), place a tray underneath, and slowly unscrew the filter cap. Clean the filter and housing. Reinsert and tighten securely.
4. Run a maintenance wash: Every 2-3 months, run a "Cotton 90°C" cycle with a washing machine cleaner or 500g of citric acid, without laundry.

CAUTION! Always disconnect from the power supply before cleaning any part of the appliance. Do not use abrasive cleaners.

Regulatory Information

This appliance complies with European Directives 2014/35/EU (Low Voltage), 2014/30/EU (EMC), and 2009/125/EC (Ecodesign). The symbol of the crossed-out wheeled bin indicates that the product must be disposed of separately at the end of its life. Contact your local authority for recycling information. For UK customers: This product is supplied with a non-rewireable plug. If the plug is not suitable for your socket, it must be cut off and disposed of safely. The fuse must be rated at 13A, ASTA approved to BS 1362. Hotpoint is a trademark of Haier Europe Trading S.r.L. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

Reset: Turn the program dial to "Stop" position for 5 seconds, or disconnect from power for 2 minutes.

Service: 03448 113 113 (UK); www.hotpoint.co.uk