Hotpoint washing machine NDB 10736 WA IT manual

The Hotpoint NDB 10736 WA IT is a freestanding washing machine with a 7 kg load capacity, energy efficiency class A+++, 1400 rpm spin speed, and multiple wash programs. It features Hotpoint's AquaCare™ technology for reduced water consumption, Anti-Allergy cycle, Direct Spray for efficient rinsing, and a delay timer. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Control panel with rotary selector and digital display, detergent dispenser, drum, filter, water inlet valves, drain pump.

Installation

Unpack and remove all transit bolts and packaging. Place on a solid, level floor.

1. Position the machine: Ensure at least 1 cm space from walls and cabinets. Adjust feet for stability.
2. Connect water supply: Attach inlet hose to cold water tap (3/4"). Do not use old hoses.
3. Connect drain hose: Place in standpipe (min. 60 cm height) or over sink edge (secure).
4. Electrical connection: Plug into a grounded 220-240V, 50Hz socket. Do not use adapters.

WARNING! Remove all 4 transit bolts from the rear before use. Failure to do so will cause severe damage.

First-Time Setup

After installation, run an empty wash cycle to clean the drum.

1. Power on: Press the ON/OFF button.
2. Select a program: Turn the selector to "Cotton 90°C".
3. Add detergent: Pour 100 ml of liquid detergent into compartment II.
4. Start: Press START/PAUSE. The cycle will run for approximately 2 hours.
5. Set language (if needed): Press and hold the "Delay Timer" and "Option 1" buttons for 3 seconds to change display language.

CAUTION! Ensure the water inlet taps are open and drain hose is properly installed before starting.

Specifications

• Model: NDB 10736 WA IT
• Dimensions (HxWxD): 85 x 59.5 x 54 cm
• Weight: 68 kg
• Rated Capacity: 7 kg
• Energy Consumption: 0.74 kWh per cycle (Cotton 60°C)
• Water Consumption: 45 litres per cycle (Cotton 60°C)
• Spin Speed: 1400 rpm (adjustable)
• Noise Level: Wash: 53 dB, Spin: 73 dB
• Supply Voltage: 220-240V ~ 50Hz
• Max Inlet Pressure: 1 MPa (10 bar)
• Min Inlet Pressure: 0.05 MPa (0.5 bar)

Controls and Settings

Access functions via the control panel. Rotary Selector: Choose wash programs. Buttons: ON/OFF, START/PAUSE, Delay Timer, Option 1 (e.g., Extra Rinse), Option 2 (e.g., Pre-Wash), Spin Speed, Temperature.

Programs: Cotton (20°C-90°C), Eco Cotton 40°C, Synthetics, Delicates, Wool, Silk, Quick Wash 30', Sport, Jeans, Anti-Allergy, Drum Clean, Spin Only, Rinse & Spin, Drain.

Options: Delay Timer (1-24h), Extra Rinse, Pre-Wash, Reduced Creases. Adjust spin speed (0-1400 rpm) and temperature (Cold to 90°C) for most programs.

Connecting Water & Drain

Water Inlet: Connect the blue-marked hose to the cold water tap. Drain: Ensure drain hose is not kinked and is at correct height.

1. Turn off the water tap and unplug the machine before connecting hoses.
2. Use only the supplied hoses. Do not lengthen them.
3. For standpipe, insert drain hose to a depth of at least 10 cm but not more than 15 cm.
4. Check for leaks after first connection by running a short cycle.

Tip: Install a drain hose support hook if draining into a sink.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Do not exceed 7 kg. Distribute evenly.
2. Add detergent: Use compartments I (Pre-wash), II (Main wash), * (Softener). Use correct dose.
3. Select program: Turn the rotary selector.
4. Set options: Adjust temperature, spin speed, and select Extra Rinse if needed.
5. Set delay (optional): Press Delay Timer button and use +/- to set hours.
6. Start: Press START/PAUSE. The door locks and cycle begins.
7. Pause/Modify: Press START/PAUSE to pause. You can add forgotten items within the first minute if water level is low.
8. End of cycle: A buzzer sounds. Door remains locked for ~2 minutes. Turn selector to OFF.

WARNING! Do not open the door during high-temperature washes. Wait for the lock symbol to disappear.

Special Functions

AquaCare™: Automatically activates on certain programs to optimize water usage. Anti-Allergy Cycle: Uses higher temperature and extended rinses to remove allergens. Direct Spray: Constantly sprays the laundry during rinse for improved rinsing efficiency. Drum Clean: Run this program monthly (without laundry) with a washing machine cleaner to prevent mold.

Care & Cleaning

Unplug before maintenance. Wipe exterior with a damp cloth. Clean the detergent dispenser monthly by pulling it out and rinsing. Clean the drain pump filter every 3 months (see instructions). Clean the door seal and glass regularly to remove lint and residue.

CAUTION! Never use abrasive cleaners, scouring pads, or solvents on the machine.

Regulatory Information

This appliance complies with EU Directives 2014/35/EU (LVD), 2014/30/EU (EMC), and 2009/125/EC (ErP). Disposal: At end of life, dispose of according to local regulations for waste electrical equipment (WEEE). Do not dispose of with household waste. For support in Italy, contact Hotpoint Assistenza Clienti at 848 800 123 or visit www.hotpoint.it.

Troubleshooting

Reset: Turn the selector to OFF and unplug for 1 minute to reset the electronic control.

Service: Hotpoint Assistenza Clienti: 848 800 123 (Italy), www.hotpoint.it