Hotpoint Washing Machine HTWP1200DWW Manual

The Hotpoint HTWP1200DWW is a 12kg capacity top-load washing machine with 1200 RPM spin speed, multiple wash programs, energy-efficient operation, delay start, child lock, and automatic load sensing. It features a durable stainless steel drum, LED display, and intuitive controls. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Stainless steel drum, Control panel with LED display, Water inlet valves, Drain hose, Adjustable leveling feet, Detergent dispenser.

Installation

Unpack and inspect contents. Place on level, solid floor.

1. Remove transit bolts: Use spanner to remove bolts at rear; keep for future moves.
2. Connect water supply: Attach hoses to hot and cold taps; ensure washers are fitted.
3. Connect drain hose: Place in standpipe or sink; secure with hook if provided.
4. Level the machine: Adjust feet until machine is stable; check with spirit level.
5. Plug into grounded power outlet.

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, run an empty wash cycle.

1. Connect power and turn on machine.
2. Add detergent: Pour 100ml of detergent into drum or dispenser.
3. Select program: Choose "Cotton" at 90°C without laundry.
4. Start cycle: Press START/PAUSE; let cycle complete to clean drum.
5. Set preferences: Use settings menu for water hardness, buzzer volume, etc.

CAUTION! Ensure transit bolts are removed before operation to prevent damage.

Specifications

• Model: HTWP1200DWW
• Capacity: 12kg (dry weight)
• Spin Speed: 1200 RPM maximum
• Dimensions (HxWxD): 85cm x 60cm x 60cm
• Water Pressure: 0.5 - 8 bar
• Power Supply: 230V~50Hz
• Energy Class: A+++
• Programs: 15 including Eco, Quick, Wool, Sport
• Noise Level: 53 dB (washing), 72 dB (spinning)
• Weight: 70kg

Controls and Settings

Control Panel: POWER, PROGRAM SELECTOR, TEMPERATURE, SPIN SPEED, OPTIONS (Delay, Pre-wash, Extra Rinse), START/PAUSE, CHILD LOCK.

Programs: Cotton (40°C-90°C), Synthetic (30°C-60°C), Delicate (cold-40°C), Quick Wash (30°C), Wool, Sport, Eco 40-60, Rinse & Spin, Drain Only.

Settings Menu: Press and hold OPTIONS for 3 seconds to access water hardness, buzzer volume, end-of-cycle signal. Temperature: Adjust per program from cold to 90°C. Spin Speed: Adjust from 400 to 1200 RPM or no spin. Options: Delay Start (1-24h), Pre-wash for heavily soiled loads, Extra Rinse for sensitive skin.

Connecting Water Supply

Requires hot and cold water connections or cold only with internal heater.

1. Turn off water taps before connecting hoses.
2. Connect blue hose to cold tap, red hose to hot tap (if available).
3. Use supplied washers; tighten by hand, then a quarter turn with pliers.
4. Ensure drain hose is not kinked and placed at correct height (60-100cm).
5. Open taps slowly and check for leaks.

Tip: Use inlet filters if provided to prevent debris entering valves.

Using Wash Programs

Follow fabric care labels for best results.

1. Sort laundry: Separate by color, fabric type, and soil level.
2. Load machine: Do not exceed 12kg; distribute evenly.
3. Add detergent: Use dispenser compartments (I: pre-wash, II: main wash, *: softener).
4. Select program: Turn selector to desired program.
5. Adjust settings: Set temperature, spin speed, and options as needed.
6. Start: Press START/PAUSE; display shows time remaining.
7. Pause/change: Press START/PAUSE to pause; turn selector to change program (may reset).
8. After cycle: Remove laundry promptly; leave door ajar to dry drum.

WARNING! Do not wash items contaminated with petrol, solvents, or chemicals. Remove coins, keys from pockets.

Safety Features

Child Lock: Press and hold CHILD LOCK for 3 seconds to lock controls (indicator lights). Door Lock: Automatically locks during cycle; unlocks at end or when paused if drum is safe. Overflow Protection: Automatically stops water if detected. Imbalance Control: Reduces spin speed if load is uneven.

Care & Cleaning

Monthly maintenance recommended.

1. Clean detergent dispenser: Remove tray, rinse under warm water.
2. Clean drum: Run "Drum Clean" program or hot wash with machine cleaner.
3. Clean filter: Locate at front bottom; place towel, open slowly, remove debris.
4. Wipe exterior: Use damp cloth; do not use abrasive cleaners.
5. Check hoses: Inspect for cracks or leaks annually.

CAUTION! Unplug before cleaning. Do not use steam or high-pressure cleaners.

Regulatory Information

Complies with EU directives for safety (EN 60335), electromagnetic compatibility (EN 55014), and energy labeling. Waste disposal: Do not dispose with household waste; contact local authorities for recycling. For support, visit www.hotpoint.co.uk or contact 03448 113 113.

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 03448 113 113; www.hotpoint.co.uk