Hotpoint Washing Machine HTWP1000MWW Manual

The Hotpoint HTWP1000MWW is a 10kg capacity top-load washing machine with 12 wash programs, 1200 RPM spin speed, energy-efficient inverter motor, delay start timer, child lock, quick wash option, and automatic load sensing. Designed for residential use with 220-240V, 50Hz power supply. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Programs 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Top-load drum, Digital Control Panel, Water Inlet Valves, Drain Pump, Detergent Dispenser, Child Lock, Delay Start Timer.

Feature	Description
Capacity	10kg maximum load capacity
Spin Speed	Up to 1200 RPM adjustable
Wash Programs	12 programs including Cotton, Synthetic, Quick Wash, Delicate
Motor Type	Energy-efficient Inverter Motor
Delay Start	Timer up to 24 hours
Child Lock	Prevents accidental program changes
Load Sensing	Automatically adjusts water and energy usage
Quick Wash	30-minute program for lightly soiled loads
Water Level	5-level manual selection
Display	LED digital display with time remaining

Installation

Unpack and inspect contents. Place on level, solid floor.

Remove transit bolts: Use wrench to remove 4 bolts at rear; keep for future moves.
Connect water supply: Attach inlet hoses to hot/cold taps (red for hot, blue for cold).
Connect drain hose: Place in standpipe or sink; ensure no kinks.
Level the machine: Adjust front feet until machine is stable.
Plug into grounded power outlet.

WARNING! Do not install in wet areas. Ensure water connections are tight to prevent leaks.

First-Time Setup

Power on machine; run initial test cycle.

Check water connections: Turn on taps, check for leaks.
Run empty wash: Select Cotton program at 90°C without laundry.
Set default preferences: Use PROGRAM knob and OPTIONS buttons to set spin speed, temperature defaults.
Activate child lock: Press and hold CHILD LOCK for 3 seconds (if needed).

CAUTION! Ensure transit bolts are removed before first use to prevent damage.

Specifications

Model: HTWP1000MWW
Capacity: 10kg (dry weight)
Dimensions (HxWxD): 85cm x 60cm x 60cm
Spin Speed: 1200 RPM (adjustable)
Programs: 12 including Cotton, Synthetic, Wool, Delicate, Quick Wash
Water Pressure: 0.5-10 bar required
Power Supply: 220-240V, 50Hz, 10A
Energy Rating: A+++
Noise Level: 65 dB (wash), 75 dB (spin)

Controls and Settings

Control Panel: PROGRAM knob, START/PAUSE, OPTIONS buttons, CHILD LOCK, DELAY START.

Program Selection: Turn knob to select: Cotton (40°C-90°C), Synthetic (30°C-60°C), Quick Wash (30°C), Delicate (cold-30°C), Wool, Rinse+Spin, Drain Only.

Options: Spin Speed (400-1200 RPM), Temperature (Cold-90°C), Extra Rinse, Pre-wash.

Delay Start: Press DELAY START, use +/- to set hours (1-24).

Child Lock: Press and hold 3 seconds to activate/deactivate.

Connecting Water Supply

Hot and cold water inlet connections required.

Turn off taps before connecting hoses.
Connect blue hose to cold tap, red to hot tap (if available).
Hand-tighten connections; check for leaks when water is turned on.
Ensure drain hose is secured in standpipe (60-100cm height).

Tip: Use only provided hoses; replace every 5 years to prevent failure.

Using Wash Programs

Follow load guidelines: Do not exceed 10kg dry weight.

Sort laundry: By color and fabric type.
Add detergent: Use dispenser drawer (I: pre-wash, II: main wash, *: softener).
Select program: Turn knob to desired program.
Adjust options: Set temperature, spin speed, extra rinse if needed.
Start: Press START/PAUSE; display shows time remaining.
Pause/change: Press START/PAUSE to pause; turn knob to change program (resets cycle).
End of cycle: Machine beeps; door unlocks after 2 minutes.

WARNING! Do not open door during spin cycle. Wait for drum to stop completely.

Safety Features

Child Lock: Disables controls when activated. Door Lock: Automatically locks during wash and spin. Overflow Protection: Automatically stops water intake if detected. Unbalanced Load Detection: Reduces spin speed or stops if load is uneven.

Care & Cleaning

Monthly maintenance recommended.

Clean detergent drawer: Remove and rinse under warm water.
Clean door seal: Wipe rubber gasket to remove lint and residue.
Run cleaning cycle: Monthly, use empty Cotton program at 90°C with washing machine cleaner.
Clean filter: Turn off power, open filter cover at front, drain water, remove debris.

CAUTION! Unplug before cleaning. Do not use abrasive cleaners on surfaces.

Regulatory Information

CE certified. Complies with EU directives for safety and electromagnetic compatibility. Energy label class A+++. Manufactured under ISO 9001 quality standards. For support, visit www.hotpoint.com or contact customer service at 1-800-123-4567.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power/child lock/door	Check power supply; ensure child lock is off; close door properly.
No water intake	Taps/hoses/filter	Ensure taps are on; check hoses for kinks; clean inlet filter.
Water doesn't drain	Drain hose/filter	Check drain hose for blockages; clean pump filter.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; adjust feet for level; redistribute load.
Error codes on display	Various faults	Consult manual error code list; reset by unplugging for 5 minutes.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 1-800-123-4567; www.hotpoint.com