Hotpoint washing machine HP 105GA CARE UK manual

The Hotpoint HP 105GA CARE is a freestanding washing machine designed for UK households, featuring a 5kg load capacity, multiple wash programs, energy-efficient operation, and user-friendly controls. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Control panel with rotary selector, LED display, detergent dispenser, drum, water inlet valves, drain pump, and adjustable feet.

Installation

Unpack and inspect contents. Place on stable, level surface near water and drain points.

1. Remove transit bolts: Use spanner to remove all transit bolts from rear; keep for future moves.
2. Connect water supply: Attach inlet hoses to cold water tap (blue marker) and machine inlet.
3. Connect drain hose: Place drain hose into standpipe or sink (minimum height 60cm).
4. Level the machine: Adjust feet using spanner until machine is stable and does not rock.
5. Plug into mains power: Use UK 3-pin plug, 220-240V AC, 50Hz.

WARNING! Do not install in areas prone to freezing or direct sunlight. Ensure all connections are secure and leak-free.

First-Time Setup

Before first use, run a maintenance wash to clean the drum and remove any residues.

1. Check installation: Ensure transit bolts removed, hoses connected, machine level.
2. Power on: Plug in and press power button; machine will beep.
3. Run initial wash: Select Cotton program at 90°C without laundry; add a small amount of detergent.
4. Set preferences: Use control panel to set clock, water hardness if applicable.
5. Load laundry: Sort fabrics by colour and care label; do not exceed 5kg.

CAUTION! Ensure packaging materials and transit bolts are fully removed before operation.

Specifications

• Model: Hotpoint HP 105GA CARE
• Capacity: 5kg
• Dimensions (HxWxD): 85cm x 60cm x 54cm
• Spin Speed: 1000 rpm
• Energy Rating: A
• Water Pressure: 0.5 - 10 bar
• Programs: Cotton, Synthetics, Delicates, Wool, Quick Wash (30°C), Rinse & Spin, Drain Only
• Power Supply: 220-240V AC, 50Hz
• Max Power Consumption: 2100W
• Noise Level: Wash: 59 dB, Spin: 77 dB

Controls and Settings

Control Panel: Power button, rotary program selector, start/pause button, option buttons (Delay, Extra Rinse, etc.), LED display.

Program Selection: Turn knob to desired program (Cotton, Synthetics, Delicates, etc.). LED lights indicate selected options.

Options: Delay Start (1-24 hours), Extra Rinse, Reduced Creases, Pre-wash. Display: Shows time remaining, cycle stage, and error codes. Settings: Press and hold specific buttons to access clock setting, child lock activation (press Delay + Extra Rinse for 3 seconds).

Connecting Water & Drain

Water Inlet: Connect blue-marked hose to cold water tap. Drain: Place hose securely into standpipe or sink.

1. Ensure water tap is off before connecting hoses.
2. Use only supplied hoses; do not reuse old hoses.
3. Drain hose must not be kinked or submerged in water.
4. Check for leaks after first connection by running a short cycle.

Tip: Install a drip tray if machine is on wooden flooring. Ensure drain hose height is between 60-100cm from floor.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Open door, load sorted laundry, close firmly until click.
2. Add detergent: Pour into correct dispenser compartments (I: pre-wash, II: main wash, *: softener).
3. Select program: Turn knob to desired program (e.g., Cotton for cottons and linens).
4. Set options: Press Delay, Extra Rinse etc. as needed.
5. Start: Press Start/Pause; door locks and cycle begins.
6. Pause/change: Press Start/Pause to pause; wait for door lock to release (may take 2 mins).
7. End of cycle: Machine beeps; door unlocks; remove laundry promptly.

WARNING! Do not open door during spin cycle. Unbalanced loads may cause machine to stop and display error.

Care & Maintenance

Regular maintenance ensures optimal performance and longevity.

• Clean detergent dispenser: Monthly, remove drawer and rinse under warm water.
• Clean door seal: Wipe rubber seal after each use to prevent mould.
• Run maintenance wash: Monthly, run Cotton 90°C program without laundry.
• Check drain filter: Every 3 months, open filter cover at front bottom, clean filter and pump housing.
• Exterior cleaning: Wipe with damp cloth; do not use abrasive cleaners.

CAUTION! Unplug machine before cleaning filter. Do not use harsh chemicals inside drum.

Safety Information

Read all safety instructions before installation and use.

• This appliance must be earthed.
• Do not use extension cords or adapters.
• Do not wash items soiled with flammable substances (petrol, oil, etc.).
• Keep children away from machine when in use; use Child Lock feature.
• Disconnect power before cleaning or maintenance.
• Do not install in wet rooms (bathrooms) or outdoors.

In case of smoke or unusual noise, disconnect immediately and contact service.

Regulatory Information

Complies with UK Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility Regulations 2016. CE marked. Manufactured for the UK market. For support, visit www.hotpointservice.co.uk or contact 03448 113 113. Keep this manual for future reference.

Troubleshooting

Reset: Unplug for 5 minutes, then restart. If problem persists, contact Hotpoint service.

Service: 03448 113 113; www.hotpointservice.co.uk