Hotpoint Washing Machine HDF330PGRBB Manual

The Hotpoint HDF330PGRBB is a 4.3 cubic foot capacity top-load washing machine with 12 wash cycles, 5 wash/rinse temperature combinations, 3 agitator speeds, 2 wash/spin speed options, and stainless steel wash basket. Features include automatic detergent and fabric softener dispenser, deep fill option, soak & pre-wash, delay start, and end-of-cycle signal. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Cycles 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, Agitator, Stainless steel wash basket, Automatic dispenser, Water inlet valves, Drain pump.

Feature	Description
Capacity	4.3 cubic feet - suitable for large loads
Wash Cycles	12 cycles including Normal, Heavy, Delicates, Quick Wash
Temperature Options	5 combinations (Hot/Cold, Warm/Cold, Cold/Cold, etc.)
Agitator Speeds	3 speeds for different fabric types
Wash/Spin Speeds	2 options (Regular and Gentle)
Automatic Dispenser	Separate compartments for detergent, bleach, fabric softener
Deep Fill Option	Extra water for heavily soiled items
Soak & Pre-wash	For stubborn stains
Delay Start	Program start up to 24 hours later
End-of-Cycle Signal	Audible alert when cycle completes

Installation

Unpack and inspect contents. Place on level floor.

Remove shipping materials: Remove transit bolts from rear panel.
Connect water supply: Attach hot and cold water hoses to corresponding faucets (red=hot, blue=cold).
Connect drain hose: Secure to standpipe or laundry tub (minimum height 39 inches).
Level the machine: Adjust leveling legs to prevent vibration.
Plug into grounded 120V AC outlet.

WARNING! Machine is heavy; use two people for moving. Ensure all connections are secure to prevent leaks.

First-Time Setup

Power on washer; run initial test cycle.

Check water connections: Turn on water faucets completely.
Run clean cycle: Select "Clean Washer" cycle with hot water to flush system.
Set default preferences: Use OPTIONS button to set default temperature, spin speed.
Load test wash: Add small load to verify operation.

CAUTION! Ensure machine is level before first use to prevent excessive vibration.

Specifications

Capacity: 4.3 cubic feet.
Dimensions: 27" W x 27" D x 43" H.
Voltage: 120V AC, 60Hz, 15 amp circuit required.
Water Pressure: 20-120 psi minimum.
Water Connections: Hot and cold 3/4" hose connections.
Cycle Times: Vary from 15 minutes (Quick Wash) to 60 minutes (Heavy Duty).
Agitator: Triple-action with 3 speed settings.
Basket Material: Stainless steel.
Controls: Electronic with LED display.
Warranty: 1-year limited parts and labor.

Controls and Settings

Control Panel: POWER, CYCLE SELECTOR, TEMPERATURE, OPTIONS, START/PAUSE, DELAY START.

Cycle Selection: Normal, Heavy, Delicates, Quick Wash, Bulky Items, Hand Wash, Rinse & Spin, Spin Only, Clean Washer, Soak, Pre-wash, Permanent Press.

Temperature Settings: Hot/Cold, Warm/Cold, Cold/Cold, Hot/Warm, Warm/Warm. Options: Deep Fill, Extra Rinse, Pre-soak, Delay Start (1-24 hours). Display: Shows cycle time remaining, selected options, error codes.

Connecting Water Supply

Required: Hot and cold water faucets, drain standpipe or tub.

Turn off water supply before connecting hoses.
Connect red hose to hot water faucet, blue to cold.
Secure drain hose to standpipe (use hose clip provided).
Check for leaks by turning water on slowly.

Tip: Install drain hose at proper height (39-96 inches) to prevent siphoning.

Using Wash Cycles

Supports various fabric types and soil levels.

Load laundry: Do not overload; leave space for agitation.
Add detergent: Use automatic dispenser (Main wash, Pre-wash, Bleach, Fabric Softener).
Select cycle: Turn knob to desired wash cycle.
Set temperature: Press TEMPERATURE button for desired combination.
Add options: Press OPTIONS for Deep Fill, Extra Rinse, etc.
Start cycle: Press START/PAUSE; display shows time remaining.
Pause/stop: Press START/PAUSE to pause; turn knob to cancel.
After cycle: Remove promptly to prevent wrinkles.

WARNING! Do not overload machine. Balance load to prevent vibration.

Maintenance Features

Clean Washer Cycle: Monthly use with washer cleaner or vinegar to remove residue. Automatic Dispenser Cleaning: Remove trays and clean with warm water. Drain Pump Filter: Access front panel to clean lint filter (monthly).

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth. Clean dispenser monthly. Run Clean Washer cycle monthly.

CAUTION! Do not use abrasive cleaners. Keep control panel dry.

Regulatory Information

UL listed; meets ENERGY STAR® requirements for energy efficiency. Manufactured to ISO 9001 standards. Copyright © Hotpoint; trademarks of GE Appliances. For support, visit www.hotpoint.com or contact 1-800-432-2737.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Washer won't start	Power/water supply	Check power outlet; ensure water faucets are on; close lid securely.
No water filling	Hoses/kinks	Check water supply; ensure hoses not kinked; clean inlet screens.
Excessive vibration	Leveling/load balance	Level machine; redistribute load; remove shipping bolts.
Water not draining	Drain hose/clog	Check drain hose for kinks; clean pump filter; ensure proper height.
Error codes displayed	Various faults	Refer to error code chart in manual; reset by unplugging for 5 minutes.
Detergent not dispensing	Clogged dispenser	Clean dispenser compartments; use correct detergent type.

Reset: Unplug for 5 minutes, then restart.

Service: 1-800-432-2737; www.hotpoint.com