Hotpoint Washing Machine HDF310PGRBB Manual

The Hotpoint HDF310PGRBB is a freestanding front-load washing machine with a 10kg capacity, featuring multiple wash programs, energy efficiency class A+++, spin speed up to 1400 RPM, direct injection motor, delay timer, child lock, and anti-flood protection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Programs 8. Maintenance & Care 9. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Front-load drum, electronic control panel, detergent dispenser, water inlet hoses, drain hose, adjustable feet, and door with safety lock.

Feature	Description
Capacity	10kg (dry laundry weight)
Spin Speed	Up to 1400 RPM
Energy Rating	A+++ (most efficient)
Wash Programs	15 programs including Cotton, Synthetic, Delicate, Quick Wash
Motor	Direct injection for quiet operation
Delay Timer	Up to 24 hours
Child Lock	Prevents accidental program changes
Anti-Flood Protection	Automatic water shut-off if leak detected
Display	LED with time remaining indicator
Door	Reversible (opens left or right)

Installation

Unpack and remove transit bolts. Place on level floor.

Remove transit bolts: Use spanner to remove 4 bolts at rear; keep for future moves.
Adjust feet: Turn clockwise/anti-clockwise to level machine; use spirit level.
Connect water supply: Attach inlet hoses to cold and/or hot water taps (if compatible).
Connect drain hose: Place in standpipe or hook over sink edge (max height 100cm).
Plug into grounded power outlet.

WARNING! Do not install in areas below 0°C. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle.

Power on: Press POWER button; display lights up.
Run empty wash: Select Cotton program at 90°C without laundry to clean drum.
Set preferences: Use OPTIONS button to adjust default spin speed, temperature.
Test child lock: Press and hold CHILD LOCK for 3 seconds to activate/deactivate.

CAUTION! Ensure all packaging and stickers are removed. Check for water leaks after first connection.

Specifications

Model: HDF310PGRBB
Capacity: 10kg
Dimensions (HxWxD): 85cm x 60cm x 60cm
Spin Speed: 400-1400 RPM (adjustable)
Energy Consumption: 0.95 kWh per cycle (Cotton 60°C)
Water Consumption: 50 liters per cycle (average)
Programs: 15 including Eco 40-60, Wool, Sport, Anti-Allergy
Noise Level: 74 dB (spin), 53 dB (wash)
Power Supply: 220-240V, 50Hz
Weight: 70kg

Controls and Settings

Control Panel: POWER, PROGRAM SELECTOR knob, START/PAUSE, OPTIONS, DELAY START, CHILD LOCK.

Program Selection: Turn knob to select: Cotton (20°C-90°C), Synthetic (30°C-60°C), Delicate (cold-30°C), Quick Wash (15 min), Eco 40-60, Wool, Silk, Sport, Anti-Allergy, Drum Clean, Rinse & Spin, Spin Only, Drain.

Options: Adjust spin speed (400-1400 RPM or No Spin), temperature (cold to 90°C), extra rinse, pre-wash. Delay Start: Set 1-24 hours. Child Lock: Press and hold 3 seconds to lock/unlock controls during operation.

Connecting Water & Drain

Water Inlet: Two hoses (blue for cold, red for hot). Drain: Hose with U-shaped end.

Ensure water taps are off before connecting hoses.
Screw hoses onto taps; hand-tighten plus quarter turn with pliers.
Place drain hose in standpipe (min diameter 4cm) or over sink edge.
Secure hose to prevent slipping.

Tip: Use only supplied hoses; replace every 5 years. Do not extend drain hose beyond 150cm.

Using Wash Programs

Follow fabric care labels for best results.

Load laundry: Do not exceed 10kg; distribute evenly.
Add detergent: Use drawer compartments I (pre-wash), II (main wash), * (softener).
Select program: Turn knob to desired program.
Start: Press START/PAUSE; door locks automatically.
Pause/Add: Press START/PAUSE to pause; wait for door unlock signal to add items.
End of cycle: Signal sounds; door unlocks after 2 minutes.

WARNING! Do not open door during high-temperature washes; steam may cause burns. Unbalance may cause reduced spin.

Maintenance & Care

Monthly: Clean detergent drawer, door seal, and filter. Every 3 months: Run Drum Clean program (without laundry).

Cleaning Filter: 1. Turn off and unplug. 2. Open filter cover at front bottom. 3. Place towel, unscrew filter slowly to drain residual water. 4. Clean filter and housing; reinstall.

CAUTION! Unplug before maintenance. Do not use abrasive cleaners on drum or seal.

Safety Features

Child Lock: Locks controls during operation. Door Safety Lock: Door locks automatically during wash; unlocks at end or when paused. Anti-Flood: Shuts off water if leak detected in hose or tub. Overheat Protection: Prevents motor overheating. Unbalance Control: Reduces spin speed if load is uneven.

Regulatory Information

CE marked; complies with EU directives for safety and electromagnetic compatibility. Energy label according to EU Regulation 2019/2014. Manufactured by Hotpoint, a brand of Whirlpool Corporation. For support, visit www.hotpoint.eu or contact customer service at +44 (0) 344 561 1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power/child lock/door	Check plug; ensure child lock off; close door firmly.
No water intake	Taps/hoses/filter	Open taps; check hose kinks; clean inlet filter.
Water doesn't drain	Drain hose/filter	Check hose for bends; clean pump filter.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; re-level feet.
Error codes (E01-E10)	Various faults	Refer to manual error code chart; reset by unplugging for 5 min.
Door won't open	Water in drum/safety lock	Wait for unlock signal; run drain program if water remains.

Reset: Unplug for 5 minutes, then restart.

Service: +44 (0) 344 561 1234; www.hotpoint.eu