Hotpoint washing machine HDA2100RWW manual

The Hotpoint HDA2100RWW is a 10kg capacity top-loading washing machine with 12 wash programs, electronic controls, LED display, adjustable spin speed up to 1200 RPM, delay start timer, child lock, and energy-efficient operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Programs 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Top-loading drum, electronic control panel, water inlet valves, drain pump, adjustable feet, and detergent dispenser.

Feature	Description
Capacity	10kg maximum load capacity
Wash Programs	12 programs including Cotton, Synthetics, Delicates, Quick Wash
Spin Speed	Adjustable up to 1200 RPM
Delay Start	Timer up to 24 hours
Child Lock	Prevents accidental program changes
LED Display	Shows remaining time, program, and settings
Water Inlet	Hot and cold water connections
Energy Rating	A+++ energy efficiency class
Dimensions	60cm width x 85cm height x 60cm depth
Power Supply	220-240V, 50Hz

Installation

Unpack and inspect contents. Place on level, stable floor.

Remove transit bolts: Use wrench to remove all four bolts from rear panel.
Adjust feet: Level the machine using adjustable feet and spirit level.
Connect water supply: Attach hoses to hot and cold water taps (included).
Connect drain hose: Place in standpipe or sink (minimum height 60cm).
Plug into grounded power outlet.

WARNING! Do not install in areas with freezing temperatures. Ensure transit bolts are removed before operation.

First-Time Setup

Before first use, run an empty wash cycle.

Connect power and water supply.
Open detergent dispenser and add 100ml of bleach to compartment II.
Select "Cotton" program at 90°C.
Press Start/Pause to begin cleaning cycle.
After completion, the machine is ready for normal use.

CAUTION! Ensure all packaging materials are removed. Check for water leaks during first cycle.

Specifications

Model: HDA2100RWW
Capacity: 10kg (cotton)
Spin Speed: 1200 RPM maximum
Programs: 12 including Eco 40-60, Wool, Sport, Bed Linen
Water Pressure: 0.5-10 bar (cold), 0.5-8 bar (hot)
Dimensions: 600 x 850 x 600 mm (WxHxD)
Weight: 68kg
Power Consumption: 2100W maximum
Energy Class: A+++
Noise Level: 53 dB (wash), 73 dB (spin)

Controls and Settings

Control Panel: Power button, Program selector, Temperature button, Spin speed button, Delay Start, Start/Pause, Child Lock.

Program Selection: Turn knob to select desired program. LED indicators show available options.

Temperature: 30°C, 40°C, 60°C, 90°C, Cold. Spin Speed: 400, 600, 800, 1000, 1200 RPM, Rinse Hold. Delay Start: 1-24 hours in 1-hour increments. Child Lock: Press and hold for 3 seconds to activate/deactivate.

Connecting Water Supply

Dual water inlet for hot and cold connection.

Ensure water taps are easily accessible.
Connect blue hose to cold water tap, red hose to hot water tap.
Use included washers and tighten connections securely.
Open taps fully and check for leaks.
For single connection, use cold water only.

Tip: Install inlet hoses with arrows pointing toward machine. Do not overtighten.

Using Wash Programs

Select appropriate program for fabric type.

Load laundry: Do not exceed maximum capacity.
Add detergent: Use compartments I (pre-wash), II (main wash), * (fabric softener).
Select program: Turn knob to desired program.
Adjust settings: Temperature, spin speed, delay start as needed.
Press Start/Pause to begin cycle.
Program end: Machine beeps and door unlocks automatically.

WARNING! Do not open door during wash cycle. Wait for door lock indicator to turn off.

Safety Features

Child Lock: Prevents program changes during operation. Door Lock: Automatic locking during wash cycles. Overflow Protection: Automatic shut-off if excess water detected. Unbalanced Load Detection: Reduces spin speed if load is uneven.

Care & Cleaning

Monthly maintenance recommended.

Clean detergent dispenser: Remove and rinse under warm water.
Clean door seal: Wipe with damp cloth to remove residue.
Run cleaning cycle: Use "Drum Clean" program monthly.
Clean filter: Turn off power, open filter cover, drain residual water, clean filter.

CAUTION! Unplug before cleaning. Do not use abrasive cleaners on surfaces.

Regulatory Information

CE certified. Complies with EU directives 2014/35/EU, 2014/30/EU, 2009/125/EC. Manufactured by Hotpoint, a Haier company. For support, visit www.hotpoint.eu or contact 0344 822 4224 (UK).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power/child lock	Check power supply; ensure child lock is off; close door properly.
No water intake	Taps/hoses/filter	Ensure taps are open; check hose kinks; clean inlet filter.
Water doesn't drain	Drain hose/filter	Check drain hose height; clean pump filter; remove blockages.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; adjust feet for level; redistribute load.
Error codes displayed	Various faults	Consult manual error code list; reset by unplugging for 5 minutes.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 0344 822 4224; www.hotpoint.eu/service