Hotpoint washing machine HDA1000ZWH manual

The Hotpoint HDA1000ZWH is a 10kg capacity front-loading washing machine with A+++ energy rating, 1400 RPM spin speed, multiple wash programs including Cotton, Synthetic, Delicate, Quick Wash, and Wool cycles, direct injection technology, anti-allergy program, delay timer, child lock, and automatic load detection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Front-loading drum, electronic control panel, detergent dispenser, water inlet valves, drain pump, adjustable feet, and door lock.

Installation

Unpack and inspect contents. Place on level, solid floor.

1. Remove transit bolts: Use spanner to remove all four bolts from rear.
2. Connect water supply: Attach inlet hoses to hot/cold taps (if applicable) and machine.
3. Connect drain hose: Place in standpipe or secure to sink edge.
4. Level the machine: Adjust front feet using wrench.
5. Plug into grounded power outlet.

WARNING! Do not install in areas with freezing temperatures. Ensure transit bolts are removed before first use.

First-Time Setup

Power on machine; run initial calibration cycle.

1. Check water connections: Ensure taps are fully open.
2. Run empty wash: Select Cotton program at 90°C without laundry.
3. Set preferences: Use control dial and buttons to set default options.
4. Test child lock: Press and hold relevant buttons to activate.

CAUTION! Ensure machine is level to prevent vibration and noise during spin.

Specifications

• Model: HDA1000ZWH
• Capacity: 10kg
• Energy Class: A+++
• Spin Speed: 1400 RPM
• Water Pressure: 0.5 - 10 bar
• Programs: 15 including Cotton, Synthetic, Delicate, Quick, Wool, Anti-Allergy
• Dimensions (HxWxD): 85 x 60 x 60 cm
• Power Supply: 220-240V, 50Hz
• Noise Level: 53 dB (washing), 73 dB (spinning)

Controls and Settings

Access programs via control dial and function buttons.

Control Panel: Power button, Program dial, Start/Pause, Delay timer, Spin speed reduction, Temperature selection, Extra rinse, Child lock.

Programs: Cotton (20°C-90°C), Synthetic (30°C-60°C), Delicate (cold-40°C), Quick Wash (30°C), Wool (cold-40°C), Anti-Allergy (60°C). Settings: Delay timer (1-24h), Spin speed (400-1400 RPM), Temperature selection, Extra rinse option. Special: Child lock (press 3 sec), Automatic load detection (default on).

Connecting Water & Drain

Water inlet: Two hoses for hot/cold (if model supports). Drain: Hose to standpipe or sink.

1. Turn off water taps before connecting hoses.
2. Use only supplied hoses; do not reuse old ones.
3. Ensure drain hose is not kinked and is at correct height (60-100 cm).
4. Check for leaks after first connection.

Tip: Use hose clips provided to secure connections.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Do not exceed 10kg; distribute evenly.
2. Add detergent: Use drawer compartments I (pre-wash), II (main wash), * (softener).
3. Select program: Turn dial to desired cycle.
4. Adjust options: Set temperature, spin speed, extra rinse if needed.
5. Start: Press Start/Pause; door locks automatically.
6. Pause/change: Press Start/Pause to stop; wait for door unlock signal.
7. End of cycle: Signal sounds; door unlocks after short delay.

WARNING! Do not open door during wash or spin; wait for unlock indicator.

Special Features

Anti-Allergy: High temperature wash to remove allergens. Delay Timer: Set start time up to 24 hours ahead. Child Lock: Prevents accidental program changes. Automatic Load Detection: Senses load size and adjusts water accordingly.

Care & Cleaning

Monthly maintenance: Run empty hot wash (90°C) with washing machine cleaner. Clean detergent drawer and door seal regularly. Check and clean pump filter if draining issues occur.

CAUTION! Unplug before cleaning. Do not use abrasive cleaners on door or drum.

Regulatory Information

CE compliant; meets EU energy efficiency and safety standards. Copyright © Hotpoint; trademarks of Whirlpool Corporation. For support, visit www.hotpoint.eu or contact local service center.

Troubleshooting

Reset: Unplug for 2 minutes, then restart.

Service: Contact authorized Hotpoint service center.