Hotpoint washing machine FML 942P UK manual

The Hotpoint FML 942P is a freestanding washing machine with a 9kg load capacity, 1400 RPM spin speed, and an A+++ energy rating. It features multiple wash programmes, a delay timer, child lock, and AquaStop technology for leak protection. This manual covers safety instructions, installation, daily use, programme guide, maintenance, and troubleshooting for optimal performance.

Features at a Glance

Key components: Control panel with rotary dial and digital display, detergent dispenser, drum, filter, inlet hoses, drain hose, and adjustable feet.

Installation

Unpack and remove all transit bolts and packaging. Position on a flat, stable floor.

1. Remove transit bolts: Use spanner to remove four bolts at rear; keep for future moves.
2. Adjust feet: Turn feet to level the machine; use spirit level to check.
3. Connect water supply: Attach inlet hoses to cold water tap (and hot if applicable).
4. Connect drain hose: Place hose into standpipe or sink; secure with hook if provided.
5. Plug into power: Use a grounded 220-240V, 50Hz socket.

WARNING! Do not install in areas prone to freezing or extreme heat. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Before first wash, run a maintenance cycle to clean the drum.

1. Power on: Plug in and press power button.
2. Run initial cycle: Select "Drum Clean" or a 90° Cotton cycle without laundry.
3. Set clock: Press and hold clock button; use programme dial to set time.
4. Load detergent: Fill compartments as per detergent instructions.
5. Start cycle: Close door and press start/pause.

CAUTION! Ensure all packaging and bolts are removed. Check for water leaks after first connection.

Specifications

• Model: Hotpoint FML 942P
• Capacity: 9kg
• Spin Speed: 1400 RPM
• Energy Rating: A+++
• Water Pressure: 0.5 - 10 bar
• Power Supply: 220-240V, 50Hz
• Programmes: Cotton, Synthetics, Delicates, Wool, Quick Wash (14 min), Sportswear, Jeans, Anti-Allergy, Drum Clean
• Noise Level: Wash: 53 dB, Spin: 75 dB
• Dimensions: 850 x 600 x 600 mm (HxWxD)
• Weight: 70 kg

Controls and Settings

Control Panel: Power button, Programme dial, Start/Pause button, Delay button, Option buttons (e.g., Extra Rinse, Pre-wash), Child Lock button, Display.

Programme Dial: Turn to select programme (Cotton, Synthetics, etc.). Display shows duration, spin speed, and temperature.

Options: Extra Rinse (adds rinse cycle), Pre-wash (for heavily soiled items), Reduced Creases (reduces spin speed). Delay Timer: Press Delay button and use dial to set start time (1-24 hours). Child Lock: Press and hold for 3 seconds to lock controls (unlock by holding again). Temperature/Spin: Adjust via buttons if available; defaults are preset per programme.

Connecting Utilities

Water: Cold fill (mandatory); hot fill optional if machine supports. Drain: Standpipe, sink, or floor drain. Power: Grounded socket.

1. Turn off water and power before connecting.
2. Attach hoses: Inlet hoses to taps (blue for cold, red for hot if used); tighten securely.
3. Drain hose: Insert into standpipe (max height 100 cm) or secure over sink edge.
4. Plug in: Ensure socket is accessible and not overloaded.

Tip: Use hose clips provided. Do not kink hoses. Check for leaks after connection.

Using Wash Programmes

Supports various fabrics and soil levels.

1. Sort laundry: Separate by colour and fabric type.
2. Load machine: Do not overload; leave space at top of drum.
3. Add detergent: Use compartment I (pre-wash), II (main wash), * (fabric softener).
4. Select programme: Turn dial (e.g., Cotton for cottons, Synthetics for blends).
5. Adjust settings: Use buttons for temperature, spin, or options.
6. Start: Close door, press Start/Pause.
7. Pause/change: Press Start/Pause to pause; turn dial to change programme (if allowed).
8. End of cycle: Machine beeps; remove laundry promptly to avoid creases.

WARNING! Do not open door during high-temperature cycles. Check pockets for objects.

Safety Features

Child Lock: Locks controls to prevent tampering. Door Lock: Automatically locks during cycle; unlocks at end or when safe. AquaStop: Monitors water flow; shuts off if leak detected. Overheat Protection: Prevents overheating of motor and components.

Care & Cleaning

Unplug before maintenance. Clean detergent drawer, door seal, and filter regularly.

Monthly: Run "Drum Clean" cycle with washing machine cleaner. Clean drawer by pulling out and rinsing. Wipe door seal and glass. Check and clean filter (see manual for location).

CAUTION! Do not use abrasive cleaners. Keep area around machine dry.

Regulatory Information

Complies with UK safety standards and EU directives (Low Voltage, EMC, Ecodesign). Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.hotpoint.co.uk or contact 0333 305 2265 (UK).

Troubleshooting

Reset: Unplug for 5 minutes, then restart. If error persists, consult manual.

Service: 0333 305 2265 (UK); www.hotpoint.co.uk