Hotpoint washing machine FDF 9640 P UK manual

The Hotpoint FDF 9640 P is a freestanding washing machine with a 9kg capacity, 1400 RPM spin speed, and an A+++ energy rating. It features multiple wash programs, a digital display, delay start, child lock, and anti-flood protection. Designed for UK households, it operates on 220-240V, 50Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Programs 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, detergent drawer, drum, water inlet valves, drain pump, and adjustable feet.

Feature	Description
Capacity	9kg drum for large loads
Spin Speed	Up to 1400 RPM for efficient drying
Energy Rating	A+++ for low energy consumption
Digital Display	Shows time, cycle stage, and settings
Delay Start	Program start up to 24 hours later
Child Lock	Prevents accidental program changes
Anti-Flood Protection	AquaStop technology for leak prevention
Quick Wash	30-minute cycle for lightly soiled items
Allergy Care	Extra rinse for sensitive skin
Adjustable Feet	For stable leveling on uneven floors

Installation

Unpack and remove transit bolts. Place on stable, level floor.

Remove transit bolts: Use spanner to remove four bolts at rear; keep for future moves.
Connect water supply: Attach inlet hose to cold water tap (3/4” thread); ensure washers are fitted.
Connect drain hose: Place into standpipe or sink; secure with hook if provided.
Level the machine: Adjust feet clockwise/counterclockwise; use spirit level.
Plug into grounded power socket.

WARNING! Do not use extension cords. Ensure water connections are tight to prevent leaks.

First-Time Setup

Plug in and run a maintenance wash before first use.

Set language: Press and hold START/PAUSE for 3 seconds to select English.
Run empty wash: Select Cotton 90°C program without detergent to clean drum.
Adjust settings: Use OPTIONS button to set beep volume, end signal, etc.
Test child lock: Press and hold DELAY START + OPTIONS for 3 seconds to activate/deactivate.

CAUTION! Ensure transit bolts are removed to prevent damage during spin.

Specifications

Model: FDF 9640 P UK.
Capacity: 9kg (cotton).
Spin Speed: 1400 RPM (adjustable).
Energy Rating: A+++ (EU scale).
Water Consumption: Approx. 50 litres per cycle (cotton 60°C).
Programs: 15 programs including Cotton, Synthetic, Delicates, Wool, Quick Wash.
Dimensions (HxWxD): 85cm x 60cm x 60cm.
Power Supply: 220-240V, 50Hz, 10A fuse.
Noise Level: 53 dB (washing), 75 dB (spinning).

Controls and Settings

Control Panel: PROGRAM knob, START/PAUSE button, OPTIONS button, DELAY START button, digital display.

Display Icons: Wash, Rinse, Spin, Child Lock, Delay Start, Time remaining.

Programs: Cotton (20°C-90°C), Synthetic (30°C-60°C), Delicates (cold-40°C), Wool, Silk, Quick Wash (30 min), Sportswear, Jeans, Anti-Allergy, Drum Clean. Options: Extra Rinse, Pre-Wash, Reduced Creases, Speed Wash. Settings: Volume control, end signal, button lock (child lock).

Connecting Water & Drain

Cold water fill only (unless model specifies hot). Drain to standpipe or sink.

Turn off water tap before connecting hose.
Connect inlet hose: Hand-tighten; do not over-tighten.
Position drain hose: Height between 60-100 cm from floor; secure to prevent slipping.
Check for leaks: Run a short cycle and inspect connections.

Tip: Use AquaStop hose (if supplied) for automatic water shut-off if leak detected.

Using Wash Programs

Select program based on fabric type and soil level.

Load laundry: Do not overload; distribute evenly.
Add detergent: Use drawer compartments I (pre-wash), II (main wash), * (fabric softener).
Select program: Turn PROGRAM knob to desired cycle.
Set options: Press OPTIONS for Extra Rinse, Pre-Wash, etc.
Delay start: Press DELAY START to set hours (up to 24).
Start: Press START/PAUSE; display shows time remaining.
Pause/change: Press START/PAUSE to stop; turn knob to change program (if allowed).
End of cycle: Machine beeps; turn off water tap; remove laundry promptly.

WARNING! Do not open door during high-temperature washes; wait for lock light to go off.

Safety Features

Child Lock: Locks buttons and door (activate/deactivate: hold DELAY START + OPTIONS 3 sec). Door Lock: Automatically locks during wash; unlocks at end. Anti-Flood: AquaStop detects leaks and stops water. Imbalance Control: Reduces spin speed if load uneven.

Care & Cleaning

Monthly maintenance: Clean detergent drawer, door seal, and drum.

Detergent drawer: Remove and rinse under warm water.
Door seal: Wipe with damp cloth to remove lint and residue.
Drum clean: Run empty Cotton 90°C program with washing machine cleaner.
Filter: Clean drain pump filter every 3 months (see manual for location).

CAUTION! Unplug before cleaning. Do not use abrasive cleaners on door or display.

Regulatory Information

Complies with UK Electrical Equipment Safety Regulations 2016. CE marked. Waste Electrical and Electronic Equipment (WEEE): Do not dispose with household waste; recycle at designated facility. For support, visit www.hotpoint.co.uk or contact 03448 225 225 (UK).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power/child lock	Check plug socket; ensure child lock is off; close door firmly.
No water intake	Tap/hose/kink	Ensure tap is on; check hose for kinks; clean inlet filter.
Water doesn't drain	Drain hose/filter	Check hose for blockages; clean pump filter.
Excessive vibration	Transit bolts/leveling	Ensure transit bolts removed; re-level machine; redistribute load.
Error codes (e.g., F01)	Fault detected	Consult manual error code list; unplug for 5 minutes, restart.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 03448 225 225; www.hotpoint.co.uk