Hotpoint washing machine BI WMHG 91484 UK manual

The Hotpoint BI WMHG 91484 is a freestanding washing machine with a 9kg capacity, 1400 rpm spin speed, and an A+++ energy rating. It features multiple wash programmes, including a 15-minute quick wash, anti-allergy cycle, and steam refresh option. Equipped with AquaCare™ technology for reduced water consumption, direct spray rinse, and automatic load detection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Control panel with LED display, detergent dispenser, drum, filter, water inlet hoses, drain hose, adjustable feet.

Installation

Unpack and remove transit bolts. Place on level, solid floor.

1. Remove transit bolts: Use spanner to remove four bolts at rear; keep for future moves.
2. Adjust feet: Turn feet to level machine; use spirit level.
3. Connect water supply: Attach inlet hoses to cold water tap (and hot if applicable).
4. Connect drain hose: Place in standpipe or sink; secure with U-bend.
5. Plug into grounded power socket.

WARNING! Do not install in areas prone to freezing. Ensure transit bolts are removed before use to prevent damage.

First-Time Setup

Plug in and run a maintenance wash before first use.

1. Power on: Press POWER button.
2. Run initial wash: Select "Drum Clean" or "Cotton 90°C" programme without laundry.
3. Add detergent: Pour 100ml of detergent into drum (not dispenser) for cleaning cycle.
4. Start cycle: Press START/PAUSE.
5. Set preferences: Use settings menu for buzzer volume, child lock, etc.

CAUTION! Ensure packaging materials are fully removed. Keep area around machine clear for ventilation.

Specifications

• Model: BI WMHG 91484 UK
• Type: Freestanding Front Loader
• Capacity: 9kg
• Spin Speed: 1400 rpm
• Energy Rating: A+++
• Water Consumption: Approx. 45 litres per cycle (typical)
• Programmes: 15+ including Cotton, Synthetic, Delicate, Wool, Quick Wash, Anti-Allergy
• Dimensions (HxWxD): 85cm x 60cm x 60cm
• Power Supply: 220-240V, 50Hz, 10A
• Noise Level: 74 dB (washing), 78 dB (spinning)

Controls and Settings

Control Panel: POWER, START/PAUSE, programme selector knob, temperature button, spin speed button, option buttons (Delay, Extra Rinse, etc.), display.

Programme Selection: Turn knob to desired programme (Cotton, Synthetic, Delicates, etc.). Adjust temperature (cold to 90°C) and spin speed (0 to 1400 rpm) with respective buttons.

Options: Delay Start (1-24h), Extra Rinse, Pre-Wash, Rapid (reduces time), Eco (reduces energy). Display shows time remaining, cycle stage, and error codes.

Settings Menu: Hold "Delay" and "Spin" buttons for 3 seconds to access: Buzzer volume, Child Lock (press and hold "Start" for 3 sec), End of Cycle signal.

Connecting Water & Drain

Water Inlet: Connect hoses to taps (blue for cold, red for hot if dual supply). Drain: Place hose in standpipe (max height 100cm) or over sink edge.

1. Ensure taps are off before connecting hoses.
2. Use only supplied hoses; do not overtighten.
3. Secure drain hose to prevent slipping.
4. Check for leaks after first connection.

Tip: Install a drip tray if placing on wooden floors. Use hose clips for secure connections.

Using Wash Programmes

Supports various fabrics and soil levels.

1. Load laundry: Do not overload; leave space at top of drum.
2. Add detergent: Use dispenser drawers (I: pre-wash, II: main wash, *: softener).
3. Select programme: Turn knob (e.g., Cotton for towels/bedding).
4. Adjust settings: Set temperature, spin speed, and options.
5. Start: Press START/PAUSE.
6. Pause/change: Press START/PAUSE to stop; wait 2 minutes to open door if safe.
7. After cycle: Remove laundry promptly; leave door ajar to dry drum.

WARNING! Do not wash items contaminated with petrol, solvents, or chemicals. Remove coins, keys from pockets.

Care & Maintenance

Regular cleaning ensures performance and longevity.

• Drum: Run "Drum Clean" monthly or use 90°C cotton cycle without laundry.
• Detergent Drawer: Remove and clean under warm water; dry before replacing.
• Door Seal: Wipe clean after each use; check for debris.
• Filter: Clean every 3 months: Turn off, unplug, open filter cover at front, drain residual water, remove and clean filter.
• Exterior: Wipe with damp cloth; do not use abrasive cleaners.

CAUTION! Unplug before cleaning filter. Never use steam or high-pressure cleaners.

Safety Features

Child Lock: Press and hold START for 3 seconds to lock controls. Door Lock: Automatically locks during cycle; unlocks when safe. Overflow Protection: Automatically stops water if detected. Imbalance Control: Reduces spin speed if load is uneven. Thermal Cut-Out: Prevents overheating.

Regulatory Information

Complies with UK Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility Regulations 2016. CE marked. Manufactured for the UK market. For support, visit www.hotpoint.co.uk or contact 03448 225 225 (UK).

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 03448 225 225; www.hotpoint.co.uk