Hotpoint washing machine BI WDHG 75148 UK N manual

The Hotpoint BI WDHG 75148 UK N is a freestanding washing machine with a 7kg capacity, 1400 rpm spin speed, A+++ energy rating, and multiple wash programs. It features Hotpoint's AquaCare™ technology for garment care, Anti-Stain system for tough stains, Direct Spray for efficient rinsing, and a Delay Timer. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Control panel with rotary selector and digital display, detergent dispenser, drum, filter, water inlet hoses, drain hose.

Installation

Unpack and remove all transit bolts and packaging. Place on level, solid floor.

1. Connect water supply: Attach inlet hoses to cold water tap (and hot if applicable). Ensure seals are tight.
2. Connect drain hose: Place hose into standpipe or sink, secure with provided U-bend.
3. Level the machine: Adjust feet to ensure machine is stable and does not rock.
4. Plug into grounded power outlet.

WARNING! Do not remove transit bolts before moving to final location. Ensure water connections are secure to prevent leaks.

First-Time Setup

After installation, run a drum clean cycle before first wash.

1. Remove transit bolts: Use spanner to remove bolts from rear, fit caps into holes.
2. Connect power and turn on: Machine will beep; display may show initial settings.
3. Run drum clean: Select Drum Clean program and press Start. This removes manufacturing residues.
4. Set preferences: Use Settings button to adjust buzzer volume, end-of-cycle signal, etc.

CAUTION! Ensure all transit bolts are removed. Failure to do so can cause severe damage during spin.

Specifications

• Capacity: 7 kg.
• Spin Speed: 1400 rpm (adjustable).
• Energy Rating: A+++.
• Water Consumption: Approx. 45 litres per cycle (cotton 60°C).
• Programs: Cotton, Synthetic, Delicates, Wool, Quick Wash, Anti-Stain, Drum Clean, etc.
• Dimensions (HxWxD): 85 x 60 x 60 cm.
• Power Supply: 220-240V, 50Hz.
• Noise Level: Wash: 53 dB, Spin: 73 dB.
• Weight: 68 kg.

Controls and Settings

Control Panel: Rotary selector for programs, Start/Pause button, Options buttons (Delay, Spin Speed, Temperature), Display showing time, settings, and status.

Program Selection: Turn knob to desired program (e.g., Cotton, Synthetic). Display shows default time, temperature, spin speed.

Options: Press corresponding button to modify: - Temperature: Select from cold to 90°C. - Spin Speed: Select from 0 (no spin) to 1400 rpm. - Delay Timer: Set delay start up to 24 hours. - Extra Rinse: Adds an additional rinse cycle. - Pre-Wash: For heavily soiled loads.

Settings Menu: Hold Settings button to access buzzer volume, child lock, factory reset.

Connecting Water & Drain

Water Inlet: Cold fill only (or hot/cold if model has dual inlet). Use supplied hoses with rubber seals. Drain: Hose diameter 19 mm; can be placed in standpipe (min 60 cm, max 100 cm height) or sink.

1. Ensure water taps are off before connecting hoses.
2. Connect hoses to machine first, then to taps. Hand-tighten only; do not overtighten.
3. For drain, ensure hose is not kinked and is secured to prevent slipping out.
4. After connections, turn on taps and check for leaks.

Tip: Use drain hose extension if needed; do not exceed maximum length of 1.5m.

Using Wash Programs

Select program based on fabric type and soil level.

1. Load laundry: Do not overload; distribute evenly.
2. Add detergent: Pour into correct compartment of dispenser (I: pre-wash, II: main wash, *: softener).
3. Select program: Turn knob (e.g., Cotton for towels/bed linen).
4. Adjust options: Set temperature, spin speed, delay if needed.
5. Start: Press Start/Pause. Door locks, cycle begins.
6. Pause/Modify: Press Start/Pause to pause; you may add items if door unlocks (within first few minutes).
7. End of cycle: Machine beeps; door unlocks after a short time. Remove laundry promptly.

WARNING! Do not open door during high-temperature washes; steam can cause burns. Check pockets for objects.

Care & Maintenance

Clean detergent dispenser monthly: Pull out drawer, rinse under tap. Clean filter: Locate behind kickplate, turn counterclockwise, remove and clean under running water. Run Drum Clean monthly: Use dedicated program or 90°C cotton cycle without laundry.

CAUTION! Unplug machine before cleaning filter. Do not use abrasive cleaners on door seal or drum.

Safety Information

This appliance must be grounded. Do not use extension cords. Keep children away from machine when in use. Do not wash items soiled with flammable substances. Always disconnect from power before maintenance.

Regulatory Information

Complies with EC Directives 2014/35/EU (Low Voltage), 2014/30/EU (EMC), and 2009/125/EC (Ecodesign). UKCA marked. Manufacturer: Hotpoint, Peterborough, PE2 9JB. For support, visit www.hotpoint.co.uk or contact 0333 305 2265.

Troubleshooting

Reset: Unplug for 1 minute, then plug back in.

Service: 0333 305 2265; www.hotpoint.co.uk