Hotpoint washing machine BHWM129 manual

The Hotpoint BHWM129 is a 12kg capacity top-loading washing machine with multiple wash programs, energy-efficient operation, child lock, delay start, and digital display. It features a stainless steel drum, adjustable spin speed, and water level selection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Wash Programs 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Digital control panel, stainless steel drum, detergent dispenser, lint filter, adjustable feet, drain hose.

Feature	Description
Capacity	12kg maximum load
Wash Programs	12 programs including Cotton, Synthetic, Quick Wash, Delicate
Spin Speed	Adjustable up to 1200 RPM
Water Level	5 levels for optimal water usage
Delay Start	Up to 24 hours
Child Lock	Prevents accidental program changes
Digital Display	Shows time remaining, program, and settings
Energy Rating	A+++ energy efficiency
Noise Level	Less than 65 dB during wash
Dimensions	850mm H x 600mm W x 600mm D

Installation

Unpack and inspect contents. Place on level, stable floor.

Remove transit bolts: Use wrench to remove 4 bolts at rear.
Adjust feet: Turn leveling feet to ensure machine is stable.
Connect water supply: Attach inlet hose to cold water tap (3/4 inch).
Connect drain hose: Place hose into standpipe or sink.
Plug into grounded power outlet.

WARNING! Do not install in areas with freezing temperatures. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, run an empty wash cycle.

Connect power and water supply.
Open detergent dispenser, add 100ml of bleach to compartment II.
Select "Cotton" program at 90°C.
Press Start/Pause to begin cycle.
After completion, wipe drum interior with soft cloth.

CAUTION! Remove all packaging materials and transit bolts before operation.

Specifications

Model: BHWM129
Capacity: 12kg (dry weight)
Programs: 12 including Eco, Cotton, Synthetic, Delicate, Wool, Quick Wash
Spin Speed: 400-1200 RPM adjustable
Water Pressure: 0.5-10 bar required
Power Supply: 220-240V, 50Hz, 10A
Energy Consumption: 0.95 kWh per cycle (Eco 40-60)
Water Consumption: 52 liters per cycle (Eco 40-60)
Dimensions: 850 x 600 x 600 mm (HxWxD)
Weight: 68kg

Controls and Settings

Control Panel: Power button, Program selector, Temperature button, Spin speed button, Delay start button, Start/Pause button, Child lock button.

Program Selection: Turn knob to select desired program. Display shows default time, temperature, and spin speed.

Temperature Adjustment: Press Temperature button to cycle through options (Cold, 30°C, 40°C, 60°C, 90°C).

Spin Speed Adjustment: Press Spin button to select speed (No Spin, 400, 600, 800, 1000, 1200 RPM).

Delay Start: Press Delay button to set start time (1-24 hours).

Child Lock: Press and hold Child Lock button for 3 seconds to activate/deactivate.

Connecting Water Supply

Cold water connection only. Do not connect to hot water supply.

Ensure water tap is closed.
Screw inlet hose to water tap (hand tight plus ½ turn with pliers).
Connect other end to machine inlet valve.
Open water tap fully and check for leaks.
Place drain hose in standpipe (minimum height 60cm, maximum 100cm).

Tip: Use only provided hoses. Do not extend or modify hoses.

Using Wash Programs

Select appropriate program for fabric type.

Load laundry: Do not exceed maximum capacity.
Add detergent: Use compartment I for pre-wash, II for main wash, • for softener.
Select program: Turn knob to desired program.
Adjust settings: Temperature, spin speed, delay start as needed.
Start cycle: Press Start/Pause button.
After cycle: Remove laundry promptly to prevent wrinkles.

Program Guide:

Cotton: For cotton and linen (90°C max)
Synthetic: For polyester, acrylic (60°C max)
Delicate: For silk, lace (40°C max, low spin)
Quick Wash: 30-minute cycle for lightly soiled items
Eco 40-60: Energy-efficient for mixed 40-60°C loads

Safety Features

Child Lock: Prevents accidental program changes. Door Lock: Automatically locks during wash cycle. Overflow Protection: Automatically stops water intake if detected. Unbalanced Load Detection: Redistributes load or reduces spin speed.

Care & Cleaning

Monthly maintenance recommended.

Clean detergent dispenser: Remove tray, rinse under warm water.
Clean lint filter: Located at bottom front right. Turn counterclockwise to remove, clean under water.
Clean drum: Run empty hot wash with washing machine cleaner.
Wipe exterior: Use damp cloth with mild detergent.

CAUTION! Unplug machine before cleaning. Do not use abrasive cleaners.

Regulatory Information

CE certified. Complies with EU directives for safety and electromagnetic compatibility. Energy label: A+++. For EU product registration, visit www.hotpoint.eu/register. Manufactured for Hotpoint, a Haier company. Copyright © 2023 Hotpoint. For support, visit www.hotpointservice.com or contact 0344 822 4224 (UK).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Door not closed, no power	Ensure door is properly closed; check power outlet; press Start/Pause.
No water intake	Water tap closed, hose kinked	Open water tap fully; straighten inlet hose; check water pressure.
Water leakage	Loose connections	Tighten hose connections; check drain hose position.
Excessive vibration	Transit bolts not removed, uneven floor	Remove all 4 transit bolts; adjust leveling feet.
Poor washing results	Overloading, wrong detergent	Reduce load size; use correct detergent amount; select proper program.
Error codes displayed	Various faults	E01: Door lock fault; E02: Drain problem; E03: Temperature sensor; Unplug for 5 minutes, then retry.

Reset: Unplug for 5 minutes to reset electronic control.

Service: 0344 822 4224; www.hotpointservice.com